Bedienungsanleitung Magnat QUANTUM 1009 S (Seite 6 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

581672

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Dear MAGNAT Customer,

Congratulations on your ﬁne new loudspeakers and thank you very much for choosing MAGNAT! You have made an excellent

choice. The high-quality speakers produced by MAGNAT are renowned all over the world.

Please study the instructions and information below carefully before using your new loudspeakers.

GENERAL INFORMATION ABOUT CONNECTING YOUR MAGNAT QUANTUM 1000 S LOUDSPEAKERS

Warning: Only hi-ﬁ ampliﬁer loudspeaker outputs may be connected to the Quantum 1000 S loudspeaker terminal.

Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent impairment of sound quality,

we recommend cables with cross-sections of at least 2.5 mm² for lengths up to 3 m and at least 4 mm² for lengths above 3 m.

Always turn off the ampliﬁer or receiver before connecting or disconnecting loudspeaker cables. Place the loudspeakers in their

planned positions and cut the cables to the right length. The cables for both channels should always be exactly the same length.

For good sound it is imperative that the cables must be connected in such a way that the speakers are “in phase”. This means

that the black negative terminals on the speakers (-) must be connected to the negative (-) terminals on the ampliﬁer, the red

positive (+) speaker terminals to the positive (+) ampliﬁer terminals. To make this easier one wire of most speaker cables is

marked with a coloured strip or a ridge in the insulation.

The Quantum 1000 S terminal is designed for 3 cord sets:

Connection via banana plugs (ﬁg. 1a)

Connection via clevis type ﬁttings (ﬁg. 1b)

Non-ready-made (ﬁg. 1c):

Strip 10 – 15 mm of insulation from the ends of non-ready-made cables. Twist the ends – this is much better than tinning them

with solder – insert them in the terminals and tighten the terminal screws ﬁrmly.

Before switching on the system double-check all your connections and make sure that the terminal screws are tight and that

there are no short circuits caused by stray wire ﬁlaments – this could cause serious damage to your ampliﬁer!

THE MAGNAT QUANTUM 1000 S LOUDSPEAKERS IN STEREO MODE

In the ideal conﬁguration the speakers and the listening position should form an equilateral triangle. When the left and right

speakers are the same distance from the listening position their sound arrives at the same time, resulting in a harmonious,

natural music reproduction. (Fig. 2)

There should be a clear line of sight between the loudspeakers and the listening position. Any sound-absorbing or reﬂecting

obstacles in the path will distort the sound. When you install the loudspeakers the following distances should be maintained:

at least 20 cm away from the rear wall and at least 30 cm from the side walls. This will prevent excessive emphasis of the bass

range.

MAGNAT QUANTUM 1000 S LOUDSPEAKERS AS A FRONT OR REAR LOUDSPEAKER

The front loudspeakers are positioned at ear height on the left and right as equidistant from the television as possible. The rear

loudspeakers are placed at ear height or a little above on the left and right besides or better behind the listening position.

therwise all the recommendations made in the previous chapter also apply.

MAGNAT QUANTUM CENTER 1000 S

The Quantum Center 1000 S loudspeaker visually and acoustically ideally matches the other Quantum 1000 S models. The

loudspeaker is placed immediately on or under the television set. Otherwise please adhere to the general recommendations

outlined in the previous chapters.

SPIKES (QUANTUM 1009 S)

You should use the supplied spikes. The spikes are height-adjustable and possess a counter nut.

Any irregularities in the ﬂoor may be offset and a ﬁrm stand may be achieved with the spikes. They also decouple the

loudspeakers from the base so that any undesirable resonance is avoided.

The spikes must be screwed into the threaded sleeves at the bottom of the box when the hard rubber feet have been removed.

In order to prevent the ﬂoor from being damaged, you should get help from someone to tilt the box slightly when ﬁtting the

spikes.

First, screw in two spikes next to each other and – before setting the box down – put the corresponding washers (rubber facing

down) in place. Then attach the two opposite spikes and lower accordingly.

Then align the box vertically and counter the spikes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Magnat QUANTUM 1009 S Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info