Bedienungsanleitung Magnat Quantum Edelstein (Seite 5 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

581671

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Dear MAGNAT Customer,

Congratulations on your fine new loudspeakers and thank you very much for choosing MAGNAT! You have

made an excellent choice. The high-quality speakers produced by MAGNAT are renowned all over the world.

Please study the instructions and information below carefully before using your new loudspeakers.

GEnERal inFORmatiOn aBOut COnnECtinG YOuR maGnat Quantum EdElstEin lOud-

sPEaKERs

Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent impairment

of sound quality, we recommend cables with cross-sections of at least 2.5 mm² for lengths up to 3 m and at

least 4 mm² for lengths above 3 m.

Always turn off the amplifier or receiver before connecting or disconnecting loudspeaker cables. Place the

loudspeakers in their planned positions and cut the cables to the right length. The cables for both channels

should always be exactly the same length.

Strip 10 – 15 mm of insulation from the ends of the cables. Twist the ends – this is much better than tinning

them with solder – insert them in the terminals and tighten the terminal screws firmly (fig. 1). Loudspeaker

cables with CE-compliant banana or single-pin plugs (4 mm) or forked fittings can also be used.

For good sound it is imperative that the cables must be connected in such a way that the speakers are “in

phase”. This means that the black negative terminals on the speakers (-) must be connected to the negative

(-) terminals on the amplifier, the red positive (+) speaker terminals to the positive (+) amplifier terminals. To

make this easier one wire of most speaker cables is marked with a coloured strip or a ridge in the insulation.

Before switching on the system double-check all your connections and make sure that the terminal screws

are tight and that there are no short circuits caused by stray wire filaments – this could cause serious damage

to your amplifier!

tHE maGnat Quantum EdElstEin lOudsPEaKERs in stEREO mOdE

In the ideal configuration the speakers and the listening position should form an equilateral triangle. When

the left and right speakers are the same distance from the listening position their sound arrives at the same

time, resulting in a harmonious, natural music reproduction. (Fig. 2)

There should be a clear line of sight between the loudspeakers and the listening position. Any sound-absorb-

ing or reflecting obstacles in the path will distort the sound.

When you install the loudspeakers the following distances should be maintained: Shelf loudspeakers should

also be as free-standing as possible, the distance to the sides to walls and items should be at least 10 cm if

possible, the tweeters should be located at ear height. If the speakers are arranged on a shelf, there should be

a minimum clearance of 10 cm to the shelves above or the ceiling.

maintEnanCE

The lacquered surface is best cleaned with a mild household cleaner. On no account use furniture polish or

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Magnat Quantum Edelstein Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info