Bedienungsanleitung Magnat Quantum Signature (Seite 6 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

581654

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Dear MAGNAT Customer,

Congratulations on your fine new loudspeakers and thank you very much for choosing MAGNAT! You have made an

excellent choice. The high-quality speakers produced by MAGNAT are renowned all over the world.

Please study the instructions and information below carefully before using your new loudspeakers.

SET-UP INFORMATION

QUANTUM SIGNATURE should if possible be set up without obstruction and slightly inclined towards the place of listening

(fig. 1).

In the ideal configuration the speakers and the listening position should form an equilateral triangle. When the left and right

speakers are the same distance from the listening position their sound arrives at the same time, resulting in a harmonious,

natural music reproduction.

There should be a clear line of sight between the loudspeakers and the listening position. Any sound-absorbing or reflecting

obstacles in the path will distort the sound.

GENERAL INFORMATION ABOUT CONNECTING YOUR MAGNAT QUANTUM SIGNATURE LOUDSPEAKERS

Warning: Only hi-fi amplifier loudspeaker outputs may be connected to the QUANTUM SIGNATURE loudspeaker

terminal.

Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent impairment of sound

quality, we recommend cables with cross-sections of at least 2.5 mm² for lengths up to 3 m and at least 4 mm² for lengths

above 3 m.

Always turn off the amplifier or receiver before connecting or disconnecting loudspeaker cables. Place the loudspeakers

in their planned positions and cut the cables to the right length. The cables for both channels should always be exactly the

same length.

For good sound it is imperative that the cables must be connected in such a way that the speakers are “in phase”. This

means that the black negative terminals on the speakers (-) must be connected to the negative (-) terminals on the amplifier,

the red positive (+) speaker terminals to the positive (+) amplifier terminals. To make this easier one wire of most speaker

cables is marked with a coloured strip or a ridge in the insulation.

The QUANTUM SIGNATURE terminal is designed for 3 cord sets:

a) Connection via banana plugs

b) Connection via clevis type fittings

c) Non-ready-made:

Strip 10 – 15 mm of insulation from the ends of non-ready-made cables. Twist the ends – this is much better than tinning

them with solder – insert them in the terminals and tighten the terminal screws firmly.

Before switching on the system double-check all your connections and make sure that the terminal screws are tight and that

there are no short circuits caused by stray wire filaments – this could cause serious damage to your amplifier!

SPIKES

You should use the supplied spikes. The spikes are height-adjustable and possess a counter nut.

Any irregularities in the floor may be offset and a firm stand may be achieved with the spikes. They also decouple the

loudspeakers from the base so that any undesirable resonance is avoided.

The spikes must be screwed into the threaded sleeves at the bottom of the box. In order to prevent the floor from being

damaged, you should get help from someone to tilt the box slightly when fitting the spikes.

First, screw in two spikes next to each other and – before setting the box down – put the corresponding washers (rubber

facing down) in place. Then attach the two opposite spikes and lower accordingly. Then align the box vertically and counter

the spikes.

MAGNAT QUANTUM SIGNATURE - BI-WIRING AND BI-AMPING

Bi-wiring means using separate cables to carry the high and low audio frequencies. Bi-amping takes this idea one step

further and uses separate power amplifiers as well as separate cables for high and low frequencies. Bi-amping in particular

produces an additional improvement in sound reproduction quality.

The special connection terminals of the QUANTUM SIGNATURE loudspeakers support both conventional connection and

operation in bi-wiring and bi-amping modes. There are four screw terminals on each speaker. The top pair are for the tweeter

(high frequencies), the lower pair for the woofer (low frequencies). The factory-installed cables strips connecting the positive

and negative terminals are for conventional 2-wire connection and must be removed for bi-wiring and bi-amping operation.

The pictures below show the correct set-up for conventional operation (fig. 2a), bi-wiring (fig. 2b) and bi-amping (fig. 2c).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Magnat Quantum Signature Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info