Bedienungsanleitung Magnavox 26MV402X (Seite 40 von 55) (Englisch)

494148

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

English

7 Usefultips

FAQ

Question Answer

Myremotecontroldoesnot

work.

WhatshouldIdo?

• Check the antenna or cable connection to the main unit.

• Check the batteries of the remote control.

• Check if there is an obstacle between the infrared sensor window and the remote control.

• Test the signal Output use IRSignalCheck.

➠

p.43 If okay, then possible infrared sensor trouble.

• Aim the remote control directly at the infrared sensor window on the front of the unit.

• Reduce the distance to the unit.

• Re-insert the batteries with their polarities (+/–) as indicated.

• When there is an infrared-equipped device such as PC near this unit, it may interrupt the remote control signal of this unit. Move

the infrared-equipped device away from this unit, change the angle of the infrared sensor or Turn Off the infrared communication

function.

Howcometheinitialsetup

appearseverytimeITurnOn

thisunit?

• Make sure to complete the initial setup before the unit goes into Standby mode.

WhycanInotwatchsomeRF

signalTVprograms.

• Autoprogram must be completed when you set up the unit for the rst time or move it to a location where previously unavailable

channels are broadcast.

• Make sure Autoprogram has been completed.

➠

p.28

• The selected channel may not be broadcasting.

• When Autoprogram is interrupted and not completed, some channels will not be received. Make sure to complete the

Autoprogram.

➠

p.28

• The selected channel cannot be viewed by the Childandratingslock setting.

➠

p.25

• The unit requires some kind of antenna Input. An indoor antenna (Digital or VHF / UHF), an external antenna (Digital or VHF / UHF)

or an RF coaxial cable from your wall cable/satellite box needs to be plugged into the unit.

Howcomethereisnoimage

fromtheconnectedexternal

devices?

• Check if the correct Input mode is selected by pressing SOURCE. Watchingchannelsfromanexternaldevice

➠

p.15

• Check the antenna, cable or other Input connection to the unit.

• When using the Component Video Connection check that the Green (Y), Blue (Pb/Cb) and Red (Pr/Cr) connectors are connected

to their corresponding colored jacks on the unit.

WhenIenterachannelnumber,

itchangesautomatically.

• Many Digital channels have alternate channel numbers. The unit changes the numbers automatically to the ones signifying the

broadcasting station channel number. These basic numbers used for previous Analog broadcasts. (e.g., Input ch# 30 automatically

changes to ch# 6.1)

Whyarecaptionsnotdisplayed

entirely?Or,captionsare

delayedbehindthedialog.

• Captions that are delayed a few seconds behind the actual dialog are common for live broadcasts. Most captioning production

companies can display a dialog to maximum of 220 words per minute. If a dialog exceeds that rate, selective editing is used to

insure that the captions remain up-to date with the current TV screen dialog.

HowcanIsettheclock? • There is no clock function on this unit.

IcannotchangetheChildlock

settingbecausemyPINcodeno

longerworks.

• Although the default PIN code (0000) is supplied with the unit, the PIN code will be required once you set a PIN code in Child

andratingslock.

➠

p.25When you forget your PIN code, enter 0711 in ChangePIN to reset the PIN code.

➠

p.27

Troubleshooting

If the unit does not perform properly when operated as instructed in this Owner’s Manual,

checkthefollowingchartandallconnectionsoncebeforecallingforservice.

Symptom Remedy

No power • Make sure the AC power cord is plugged in.

• Make sure that the AC outlet supplies the proper voltage, plug another electrical appliance into the AC outlet to ensure that the AC

outlet operates normally.

• If a power failure occurs, unplug the AC power cord for 1 minute to allow the unit to reset itself.

Control buttons do not work. • Press only one button at a time. Do NOT press more than one button at the same time.

• Ensure that no buttons on the remote control are depressed and move freely.

Power is ON but no screen

image.

• Check whether the connection of the antenna, cable receiver or satellite box is connected correctly.

• Check whether all the cables to the unit are connected to the correct Output jack of your device like Blu-ray / DVD recorder.

• Make sure that the selected Input mode is connected to the working Input jack.

• Check if your computer is NOT in sleep mode when the Input mode of this unit is in PC mode. Tap any key on the keyboard to

wake up your computer.

Continued on next page.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Magnavox 26MV402X Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info