Bedienungsanleitung Magnum Standard Control (Seite 1 von 2) (Englisch)

602853

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

MAGNUM Standard Control

On/O Thermostat

Installation manual

PLEASE READ THIS MANUAL CAREFULLY BEFORE

INSTALLATION, AND STORE WITH OTHER WARRANTEE

FORMS.

The MAGNUM Standard Control is an electronic thermostat

with four functions: Room sensor, oor sensor, power regulator

and room sensor with max./min. limiter. This thermostat can

also be set up for setback temperature.

1. Startup

Remove the adjustment wheel with a screwdriver. The front cover

can the be removed by pushing in the locking clips on each side

of the thermostat (as shown in g.2). Be careful when doing this

in order not to damage the thermostat. When the thermostat has

been connected to the power source, push the on/o button.

Never dismantle the thermostat when the power is switched on.

2. Sensor choice

When choosing a sensor type, the thermostat should not be

connected to a power source.

• Floor sensor (standard)

Jumper placement: Covering the two pins on the left.

Application: The temperature is regulated by the oor sensor.

• Room sensor

Jumper placement: Covering the two pins in the right

Application: The temperature is regulated by the room sensor.

• Room sensor with limiter

Jumper placement: Covering the two pins on the right + the

oor sensor connected

Application: The temperature is regulated by the room sensor,

but the oor sensor overrides the room sensor if the oor

temperature exceeds the maximum limit temperature. The limiter

can be regulated between 20°C and 30°C. For parquet ooring, a

maximum of 27°C is recommended by most ooring manufac-

turers. Please follow the recommendations provided by your

manufacturer.

• Power regulator

Jumper placement: Covering the two center pins

Application: The eect regulator has a 30 min cycle. The desired

on/o interval can be set from 0 to 10, where each level increases

the on-time by 3 minutes.

Example: When the thermostat is set to level 3, the heating

element is switched on for 9 minutes, then o for 21 minutes in

the 30 minute cycle. If the thermostat is set to level 6, the heating

element is switched on for 18 minutes, then o for 12 minutes.

Fig.2

Bi-LED diode

Adjustment wheel

Fig.1

123 4567

HEATING L

SENSOR

PILOT WIRE

HEATING N

Fig.2

Bi-LED diode

Adjustment wheel

Fig.1

123 4567

HEATING L

SENSOR

PILOT WIRE

HEATING N

Fig.2

Bi-LED diode

Adjustment wheel

Fig.1

123 4567

HEATING L

SENSOR

PILOT WIRE

HEATING N

3. Connecting the thermostat

The termostat must be connected to the power source according to

the connection diagram. All heating systems must be equipped with

a residual current disrupter with 30mA. Max load for the thermostat is

16A/3600W at 230V. If the load is higher, the thermostat must be con-

nected to a contactor. The thermostat does not have galvanic insulation

between high and low current. The sensor must therefore be considered

as live (230V) and needs to be installed in accordance with the rules for

high current installations and national installation requirements.

Caution: When reattaching the thermostat cover, make sure the ven-

tilation on the top and bottom of the thermostat is not covered up.

4. Setback temperature

The Multireg thermostat does not have a built-in setback temperature

option, but by connecting an external timer to the S and L clamps, the

temperature can be lowered by 3°C at desired times.

5. Calibrating the temperature

When connecting the oor heating system for the rst time, the tem-

perature should be set at a maximum of 15°C to 20°C. The thermostat

should be calibrated after 2-3 days. Pull out the adjustment wheel

carefully (without turning it) until it comes loose. Use a thermometer to

check the actual temperature, and push the adjustment wheel back onto

the thermometer in accordance with the measured temperature. If the

oor heating has been switched o during the summer, this procedure

should be repeated when it is switched back on.

6. Bi-LED diode

• Green light when the thermostat is in a standby mode.

• Constant red light when the relay is engaged and the power is on.

• Blinking red light when there is a sensor malfunction or the oor sensor

is disconnected.

7. Technical data

Voltage 230 VAC AC ± 15% 50 Hz

Max. load 3600W (resistive load)

Max. current 16 Amp

Power consumption 0,5W

IP-class IP 21

Power regulator Time cycle: 0-30 min

Min/Max inst. temp. -20°C - +60°C

Min/Max oper. temp. 0° - 50°C

Temperature intervals Floor sensor: 5°C - 40°C

Room sensor 5°C - 40°C

Hysteresis 0.5°C

Sensor values 0°C 29,1 Kohm

10°C 18,6 Kohm

15°C 15,1 Kohm

20°C 12,2 Kohm

25°C 10,0 Kohm

Switch 2-pole switch

Colors White RAL 9010 (5430333)

White RAL 9003 (5430444)

Floor sensor Length 3 meters. The cable can be extended

10 meters by using a proper installation cable.

Fig.2

Bi-LED diode

Adjustment wheel

Fig.1

123 4567

HEATING

SENSOR

PILO

T WIRE

HEATING

Torque: Max. 2Nm

Clamp 1+ 2Sensor - Floor sensor

Clamp 3: Pilot wire (connected to L for

setback temperature)

Clamp 4: Heating L

Clamp 5: L

Clamp 6: Heating N

Clamp 7: N

Fig.2

Bi-LED diode

Adjustment wheel

Fig.1

123 4567

HEATING L

SENSOR

PILOT WIRE

HEATING N

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Magnum Standard Control Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info