534675
41
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
41PRINTING FROM SD
TROUBLESHOOTING
The Replicator 2X doesn’t recognize
the SD Card
If your MakerBot Replicator 2X does not
detect that there is a card in the SD slot,
make sure the SD card is:
an SDSC card formatted for FAT16
no larger than 2GB.
Your MakerBot Replicator 2X can read only
cards that meet these requirements.
The default SD card that is shipped with
your MakerBot Replicator 2X is formatted
correctly and is of the correct size.
If the card is formatted correctly but your
MakerBot Replicator 2X fails to recognize
it, something may be wrong with the card.
Contact MakerBot Support.
The Replicator 2X doesn’t see the files
on the SD Card
If your MakerBot Replicator 2X detects
the SD card but can’t see the files on the
SD card, make sure that each file is in the
correct format.
Your MakerBot Replicator 2X can
read only files:
that use the X3G format. To create an X3G
file in MakerWare, click Export to File in
the make dialog and select X3G from the
file type dropdown menu.
• with les name fewer than 26 characters;
30 characters if you count the file
extension. If you are trying to print an
X3G file with a long file name, shorten
it and try again.
The default SD card that is shipped with
your MakerBot Replicator 2X contains only
files of the correct format and with names
less than 26 characters.
If the files are formatted for X3G and the
file names have fewer than 26 characters
but your MakerBot Replicator 2X fails to
recognize them, something may be wrong
with the card. Contact MakerBot Support.
Printed objects don’t stick to the build plate
If printed objects are not sticking to the
build plate, try these solutions:
Re-level your build plate by going to
Utilities > Level Build Plate. Inconsistent
plate height will lead to inconsistent
adhesion. If any one part of your object
does not adhere well to the plate, the
whole object might peel o the plate.
Try leveling the plate again and using
a thinner piece of paper or feeler gauge
to check the distance.
Ensure that the plate is clean. Bubbles,
scratches, dust, and oil from your hands
can prevent objects from sticking to the
Kapton tape. Wipe down the build plate
with a clean, lint-free cloth.
41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für MakerBot Replicator 2X wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info