Bedienungsanleitung Makita 1050D (Seite 6 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448163

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

8. Be careful not to drop, shake or strike battery.

9. Do not charge inside a box or container of any

kind. The battery must be placed in a well venti-

lated area during charging.

ADDITIONAL SAFETY RULES FOR TOOL

ENB043-1

1. Be aware that this tool is always in an operating

condition, because it does not have to be

plugged into an electrical outlet.

2. Rags, cloth, cord, string and the like should

never be left around the work area.

3. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

4. Use only sharp blades. Handle the blades very

carefully.

5. Be sure the blade installation bolts are securely

tightened before operation.

6. Hold the tool firmly with both hands.

7. Keep hands away from rotating parts.

8. Before using the tool on an actual workpiece, let

it run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced blade.

9. Make sure the blade is not contacting the work-

piece before the switch is turned on.

10. Wait until the blade attains full speed before cut-

ting.

11. Keep at least 200 mm away from the tool at all

times.

12. Always switch off and wait for the blades to

come to a complete stop before any adjusting.

13. Never stick your finger into the chip chute. Chute

may jam when cutting damp wood. Clean out

chips with a stick.

14. Do not leave the tool running. Operate the tool

only when hand-held.

15. When leaving the planer, switch off and set it

with the front base up on a wooden block, so

that the blades do not contact anything.

16. Always change both blades or covers on the

drum, otherwise the resulting imbalance will

cause vibration and shorten tool life.

17. Wait for complete run-down before putting the

tool aside.

18. Use only Makita blades specified in this manual.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before insertion or removal of the battery cartridge.

• To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge.

• To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into

place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool,

causing injury to you or someone around you.

• Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted

correctly.

Charging (Fig. 2)

Plug the fast charger into the proper AC voltage source. The charging light will flash in green color. Insert the battery

cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective mark-

ings on the fast charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When the bat-

tery cartridge is inserted, the charging light color will change from green to red and charging will begin. The charging

light will remain lit steadily during charging. When the charging light color changes from red to green, the charging

cycle is complete. Refer to the table below for the charging time. If you leave the battery cartridge in the charger after

the charging cycle is complete, the charger will switch into its “trickle charge (maintenance charge)” mode which will

last approximately 24 hours. After charging, unplug the charger from the power source.

CAUTION:

• The fast charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s

batteries.

• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it

may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-

tery cartridge fully after discharging it completely and recharging a couple of times.

• If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location

exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a

while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the

battery cartridge from the fast charger.

Battery type Capacity (mAh) Number of cells Charging time

1202, 1202A, 1222 2,000 10 Approx. 45 min.

1200, 1220 1,300 10 Approx. 30 min.

1233 2,200 10 Approx. 50 min.

1234 2,600 10 Approx. 60 min.

1235 3,000 10 Approx. 70 min.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 1050D Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita 1050D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info