Bedienungsanleitung Makita 1100D (Seite 8 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448165

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

For the correct planer blade setting

Your planing surface will end up rough and uneven, unless the blade is set properly and securely. The blade must be

mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the rear base.

Refer to some examples below for proper and improper settings.

Connecting a vacuum cleaner

For tools with European type (round) chip cover

(Fig. 10 & 11)

When you wish to perform clean planing operation, con-

nect a Makita vacuum cleaner to your tool as shown in

Fig. 10 & 11.

For tools with standard (non-round) chip cover

(Fig. 12)

Any Makita vacuum cleaner cannot be connected to the

tool with the standard (non-round) chip cover.

OPERATION

Planing operation (Fig. 13)

First, rest the tool front base flat upon the workpiece sur-

face without the blades making any contact. Switch on

and wait until the blades attain full speed. Then move the

tool gently forward. Apply pressure on the front of tool at

the start of planing, and at the back at the end of planing.

Planing will be easier if you incline the workpiece in sta-

tionary fashion, so that you can plane somewhat downhill.

The speed and depth of cut determine the kind of finish.

The power planer keeps cutting at a speed that will not

result in jamming by chips. For rough cutting, the depth of

cut can be increased, while for a good finish you should

reduce the depth of cut and advance the tool more

slowly.

Shiplapping (Rabbeting) (Fig. 14, 15, 16, 17 & 18)

To make a stepped cut as shown in Fig. 14, use the edge

fence (guide rule).

Draw a cutting line on the workpiece. Insert the edge

fence into the hole in the front of the tool. Align the blade

edge with the cutting line. (Fig. 15)

Adjust the edge fence until it comes in contact with the

side of the workpiece, then secure it by tightening the

screw. (Fig. 16)

When planing, move the tool with the edge fence flush

with the side of the workpiece. Otherwise uneven planing

may result.

Maximum shiplapping (rabbeting) depth is 20 mm.

You may wish to add to the length of the fence by attach-

ing an extra piece of wood. Convenient holes are pro-

vided in the fence for this purpose, and also for attaching

an extension guide (optional accessory). (Fig. 17)

CAUTION:

• The blade edge should be made to protrude outside

slightly (0.3 mm – 0.6 mm). Otherwise, nicks and gen-

erally poor shiplapping results. (Fig. 18)

Chamfering (Fig. 19 & 20)

To make a chamfering cut as shown in Fig. 19 & 20, align

the “V” groove in the front base with the edge of the work-

piece and plane it.

(A)

(B)

(A)

(B)

(A)

(A) Front base (Movable shoe)

(B) Rear base (Stationary shoe)

Correct setting

Nicks in surface

Gouging at start

Gouging at end

Although this side view cannot show it,

the edges of the blades run perfectly

parallel to the rear base surface.

Cause: One or both blades fails to

have edge parallel to rear

base line.

Cause: One or both blade edges fails

to protrude enough in relation

to rear base line.

Cause: One or both blade edges

protrudes too far in relation to

rear base line.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 1100D Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita 1100D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info