Bedienungsanleitung Makita 1911B (Seite 4 von 18) (Englisch, Holländisch)

448171

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

ENGLISH

Explanation of general view

1 Bolt

2 Drum

3 Planer blade

4 Drum cover

5 Adjust plate

6 Blade edge

7 Screws

8 Heel

9 Back side of gauge base

0 Inside edge of gauge plate

q Gauge plate

w Gauge base

e Knob

r Switch trigger

t Lock button/

Lock-off button

y Start

u End

i ‘‘V’’ groove

o Front base

p Align the ‘‘V’’ groove with the

edge of the workpiece.

a Sharpening holder

s Wing nut

d Blade (A)

f Blade (B)

g Side (C)

h Side (D)

j Screwdriver

k Nozzle assembly

l Makita vacuum cleaner

SPECIFICATIONS

Model 1911B

Planing width ................................................ 110 mm

Planing depth ................................................... 2 mm

No load speed (RPM) .................................... 16,000

Overall length ............................................... 355 mm

Net weight ....................................................... 4.2 kg

•

Due to the continuing program of research and

development, the specifications herein are subject

to change without prior notice.

•

Note: Specifications may differ from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, and can only be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to enclosed Safety

instructions.

These symbols mean:

Read instruction manual.

DOUBLE INSULATION

ADDITIONAL SAFETY RULES

1. Rags, cloth, cord, string and the like should

never be left around the work area.

2. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

3. Handle the blades very carefully.

4. Be sure the blade installation bolts are

securely tightened before operation.

5. Hold the machine firmly with both hands.

6. Keep hands away from rotating parts.

7. Before using the machine on an actual work-

piece, let it run for a while. Watch for vibration

or wobbling that could indicate poor installa-

tion or a poorly balanced blade.

8. Make sure the blade is not contacting the

workpiece before the switch is turned on.

9. Wait until the blade attains full speed before

cutting.

10. Keep at least 200 mm away from the machine

at all times.

11. Always switch off and wait for the blades to

come to a complete stop before any adjusting.

12. Never stick your finger into the chip chute.

Chute may jam when cutting damp wood.

Clean out chips with a stick.

13. Do not leave the machine running. Operate the

machine only when hand-held.

14. When leaving the planer, switch off and set it

with the front base up on a wooden block, so

that the blades do not contact anything.

15. Always change both blades or covers on the

drum, otherwise the resulting imbalance will

cause vibration and shorten machine life.

16. Wait for complete run-down before putting the

machine aside.

17. Use only Makita blades specified in this

manual.

SAVE THESE INSTRUCTIONS.

1911B (Eng) (’97. 11. 7)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 1911B Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita 1911B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info