Bedienungsanleitung Makita 194043-3 (Seite 3 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

598727

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENGLISH

Explanation of general view

1Frame

2Bolts

3 Support

4 Inner grooves (A)

5 Outer grooves (B)

6Frame pipe

7 Lock plate

8 Support plate (For LS0714 only)

9 The smallest hole in the support

10 Adjusting bolt

11 Front holes in your tool base

12 Front holes in the supports

13 Bolt

14 Nut

15 Fix plates

16 Outer hole (a)

17 Inner hole (b)

18 The largest holes

19 Outer frame

20 Inner frame

Symbols

WARNING:

• Read and thoroughly understand this manual and the

instruction manual of the tool you use before perform-

ing the following.

• Before installing a tool on this stand, always switch off

and unplug the tool.

• The stand should be bolted in a stable and level sur-

face using the bolts provided on three of four feet.

• This stand can be used only with the models of Miter

saws, Compound miter saw, slide compound miter saw

and thicknesser or planer specified in this manual.

• Open and lock before fastening the tool to the stand.

• Fasten the tool to the supports before use.

• Do not climb, sit or stand on this stand.

• Make sure that the stand is set up so that the corporate

nameplate on the stand always faces the operator.

• Do not carry the stand with the tool.

• Before storing or transporting, fold the frame and

secure the supports by tightening bolts on the support

backside.

How to install the stand

When installing miter saw, compound miter saw and

slide compound saw;

1. Loosen the bolts on the backside of the supports.

(Fig. 1)

2. Open the frame and pivot the supports so that the

frame pipe fits in the inner grooves (A) in the sup-

ports. (Fig. 1)

3. Adjust the position of two supports according to the

distance of front holes in the base of the tool you use.

Push down the lock plate to lock it. (Fig. 1)

Note:

Only when using Model LS0714, install the support

plate so that its holes meet the smallest holes in the

supports and secure it firmly with two bolts. (Fig. 2)

4. Turn the stand so that the adjusting bolt at its foot or

the corporate nameplate faces you. Place the tool in

the middle of the support.

All miter saw models specified in this manual should

be placed so that two front holes of the tool base

match the first front holes on the support. (Fig. 3)

Two rear holes of the tool base meet holes accordingly.

Note: When the holes in the tool base do not align

with those in the support, unlock the lock plate by

raising it, readjust it for fine adjustment and push it

down again to lock it. Secure bolts on the backside

of supports firmly after the adjustment. (Fig. 3)

5. Secure the tool base to the support of the stand with

four hex bolts and four nuts provided with the stand.

Make sure that the two front bolts and nuts have been

firmly tightened in the first front holes in the support.

(Fig. 3)

6. When the stand cannot be set up stable, turn the

adjusting bolt at the foot of stand for proper stability.

After adjustment, make sure that the stand and tool

keep stable. (Fig. 4)

7. Secure the feet of stand to the stable and level sur-

face using holes in the fix plates with three hex bolts.

(Fig. 4)

When installing thicknesser or planer

CAUTION:

When using the thicknesser or planer specified in

this manual, set up the stand in the low position

mode.

Failure to do so may result in fall-down and personal

injury.

1. See (1) and (2) stated above in the titled “When

installing miter saw”.

2. Loosen and remove the bolt and nut that secure the

lock plate and outer frame. Change the installation

position of the lock plate from the outer hole (a) to the

inner hole (b) and retighten the bolt firmly. Repeat the

same action on another side. (Fig. 5)

3. Close the frame slightly, raise the support and detach

the frame pipe from the inner grooves (A) in the sup-

port. While holding the frame on, widen the feet of

frame carefully and fully. Fit the frame pipe in the

outer grooves (B) in the support. (Fig. 6)

4. Adjust the position of the supports according to the

distance of front holes in the base of the tool you use.

Push down the lock plate to lock it. (Fig. 7)

5. Turn the stand so that the adjusting bolt at its foot or

the corporate nameplate faces you. Place the tool in

the middle of the support. Thicknesser or planer

model specified in this manual should be placed so

that four holes of the tool base match the largest

holes on the support of the stand. (Fig. 7)

Note: When the holes in the tool base do not align

with those in the support, unlock the lock plate by

raising it, readjust it for fine adjustment and push it

down again to lock it. Secure bolts on the backside

of supports firmly after the adjustment. (Fig. 7)

6. Secure the tool base to the support of the stand with

four hex bolts and four nuts provided with the stand.

Make sure that these four bolts are inserted from the

underside as shown in the figure. (Fig. 8)

7. The subsequent actions are the same as (6) – (7) in

the “When installing miter saw, compound miter saw

and slide compound saw;”.

❏ Read instruction manual.

❏ Maximum allowable loading.

MAX

100Kg

(220lbs.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 194043-3 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info