Bedienungsanleitung Makita 2712 (Seite 10 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690940

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Switch action

CAUTION:

• Remove workpiece from the table.

• Before plugging in the tool, always be sure that the tool

is switched off. (Fig. 15)

To start the tool, press the ON (I) button.

To stop it, press the OFF (O) button or the switch cover.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

The tool is shipped from the factory with the saw blade

and blade guard not in the installed condition.

Removing or installing saw blade

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing the blade.

• Use only the Makita hex wrench provided to install or

remove the blade. Failure to do so may result in

overtightening or insufficient tightening of the hex bolt.

This could cause an injury.

• Use the following saw blade. Do not use saw blades

which do not comply with the characteristics specified

in these instructions.

014540

To remove the saw blade, remove the table insert on the

table. Hold the outer flange with the wrench and loosen

the hex bolt clockwise with the hex wrench. Then remove

the outer flange. (Fig. 16)

To install the saw blade, assemble the inner flange, saw

blade, outer flange, washer and hex bolt onto the arbor.

Make sure that the teeth of the blade are pointing down at

the front of the table. (Fig. 17)

CAUTION:

• Keep the flange surface clean of dirt or other adhering

matter; it could cause blade slippage. Be sure that the

blade is installed so that the teeth are aligned in the

cutting (turning) direction.

To secure the blade in place, hold the outer flange with

the wrench, then tighten the hex bolt counterclockwise

with the hex wrench. BE SURE TO TIGHTEN THE HEX

BOLT SECURELY. (Fig. 18)

CAUTION:

• Be sure to hold the hex bolt carefully with the hex

wrench. If your grip should slip, the hex wrench may

come off the hex bolt, and your hand could strike the

sharp blade edges.

Installing blade guard

CAUTION:

• Before installing the blade guard, adjust the depth of

cut to its maximum elevation.

Place the blade guard into the groove on the riving knife.

Secure the blade guard by pivoting the lever on the blade

guard. (Fig. 19 & 20)

CAUTION:

• If the blade and riving knife are not aligned properly, a

dangerous pinching condition may result during

operation. Make sure they are properly aligned. You

could suffer serious personal injury while using the tool

without a properly aligned riving knife.

• If they are not aligned for any reasons, always have

Makita authorized service center repair it.

• Don’t remove the riving knife.

There must be a clearance of about 4 - 5 mm between the

riving knife and the blade teeth. Adjust the riving knife

accordingly and tighten the hex nut securely. Attach the

table insert on the table, then check to see that the blade

guard works smoothly before cutting. (Fig. 21)

Installing and adjusting rip fence (Fig. 22)

Install the rip fence on the table so that the rip fence

holder engages with the guide rail. Tighten the knob of the

rip fence firmly clockwise. (Fig. 23)

To check that the rip fence is parallel with the blade,

secure the rip fence 2 - 3 mm from the blade.

Raise the blade up to maximum elevation. Measure the

distance (A) and (B) between the rip fence and blade.

These two measurements should be identical.

If the rip fence is not parallel with the blade, proceed as

follows;

1. Loosen the knob of the rip fence.

2. Adjust the rip fence until it becomes parallel with the

blade.

3. Tighten the knob.

CAUTION:

• Make sure that the rip fence is parallel with the blade,

or a dangerous kickback condition may occur.

Connecting to vacuum cleaner (Fig. 24)

Cleaner operations can be performed by connecting the

tool to Makita vacuum cleaner or dust collector.

OPERATION

CAUTION:

• Always use “work helpers” such as push sticks and

push blocks when there is a danger that your hands or

fingers will come close to the blade.

• Always hold the workpiece firmly with the table and the

rip fence or miter gauge. Do not bend or twist it while

feeding. If the workpiece is bent or twisted, dangerous

kickbacks may occur.

• NEVER withdraw the workpiece while the blade is

running. If you must withdraw the workpiece before

completing a cut, first switch the tool off while holding

the workpiece firmly. Wait until the blade has come to a

complete stop before withdrawing the workpiece.

Failure to do so may cause dangerous kickbacks.

• NEVER remove cut-off material while the blade is

running.

• NEVER place your hands or fingers in the path of the

saw blade. Be especially careful with bevel cuts.

• Always secure the rip fence firmly, or dangerous

kickbacks may occur.

Model Dia.

Blade

thickness

Kerf

2712 315 mm 2 mm or more 2.8 mm or more

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 2712 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info