Bedienungsanleitung Makita 3708 kantenfrees (Seite 9 von 12) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

426934

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Circular work (Fig. 13, 14 & 15)

• Circular work may be accomplished if you assemble the

straight guide and guide plate as shown in Fig. 13 or 14.

Fig. 13 for cutting circles between 70 mm and 121 mm

in radius.

Fig. 14 for cutting circles between 121 mm and 221 mm

in radius.

Note:

Circles between 172 mm and 186 mm in radius cannot

be cut using this guide.

• Min. and max. radius of circles to be cut (distance

between the center of circle and the center of bit) are

as follows:

Min.: 70 mm

Max.: 221 mm

Align the center hole in the straight guide with the center

of the circle to be cut. Drive a nail less than 6 mm in

diameter into the center hole to secure the straight guide.

Pivot the tool around the nail in clockwise direction.

Trimmer guide (Fig. 16, 17 & 18)

Trimming, curved cuts in veneers for furniture and the like

can be done easily with the trimmer guide. The guide

roller rides the curve and assures a fine cut.

Loosen the wing bolts and secure the tool base horizon-

tally. Install the trimmer guide on the tool base with the

clamp screw (A). Loosen the clamp screw (B) and adjust

the distance between the bit and the trimmer guide by

turning the adjusting screw (1 mm per turn). At the

desired distance, tighten the clamp screw (B) to secure

the trimmer guide in place.

When cutting, move the tool with the guide roller riding

the side of the workpiece.

Templet guide (Fig. 19, 20, 21 & 22)

The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet patterns.

Remove the tool base from the tool. Loosen the wing bolts and secure the tool base horizontally. Loosen the two

screws on the tool base.

Place the templet guide on the tool base. There are four convex portions on the templet guide. Secure two of the four

convex portions using the two screws. Install the tool base on the tool.

Secure the templet to the workpiece. Place the tool on the templet and move the tool with the templet guide sliding

along the side of the templet.

NOTE:

The workpiece will be cut a slightly different size from the templet. Allow for the distance (X) between the router bit and

the outside of the templet guide. The distance (X) can be calculated by using the following equation:

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacing carbon brushes

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes. (Fig. 29)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps. (Fig. 30)

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Center.

ACCESSORY

Makita offers an extensive range of trimmer bits which

comply with the latest safety regulations. Specifications

of each type can be found on the following pages.

Distance (X) =

outside diameter of the templet guide – router bit diameter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 3708 kantenfrees Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info