Bedienungsanleitung Makita 4101 RH (Seite 7 von 17) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448192

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

ENGLISH

Explanation of general view

1 Wing bolt

2 Water pipe

3Hex wrench 5

4Loosen

5Tighten

6 Wrench 22

7 Inner flange

8 Diamond wheel

9 Outer flange

10 Hex socket head bolt

11 Base

12 Wing nut

13 This end of blade case should

be above the red line.

14 Red line

15 “TEST” button

16 “ON” button

17 Pilot lamp

18 Portable residual current device

(PRCD)

19 Switch trigger

20 Lock-off button

21 Top guide

22 For straight cuts

23 For 45° bevel cuts

24 Clamp

25 Cover (A)

26 Screw

27 Cover (B)

28 Limit mark

29 Brush holder cap

30 Screwdriver

SPECIFICATIONS

Model 4101RH

Wheel diameter .................................................. 125 mm

Max. cutting capacities

At 90° ..............................................................41.5 mm

At 45° ................................................................. 26 mm

No load speed (RPM) ...........................................12,000

Overall length .....................................................236 mm

Net weight .............................................................. 2.9 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. This tool

should be grounded while in use to protect the operator

from electric shock. Use only three-wire extension cords

which have three-prong grounding-type plugs and three-

pole receptacles which accept the tool’s plug.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. This tool is equipped with a portable residual

current device. Do not connect the tool to a

power supply without using the PRCD (Portable

Residual Current Device). In case of damage of

the cord, it has to be replaced by the manufac-

turer’s service organization.

2. For additional protection against electric shock,

be sure to WEAR RUBBER GLOVES AND RUB-

BER BOOTS during operation.

3. Check the wheel carefully for cracks or damage

before operation. Replace cracked or damaged

wheel immediately.

4. Use only flanges specified for this tool.

5. Be careful not to damage the spindle, flanges

(especially the installing surface) or bolt. Dam-

age to these parts could result in wheel break-

age.

6. When using the water feed, be careful not to let

water get into the motor. If water runs into the

motor, an electric shock hazard may result.

7. Hold the tool firmly.

8. Keep hands away from rotating parts.

9. Make sure the wheel is not contacting the work-

piece before the switch is turned on.

10. Wait until the wheel attains full speed before cut-

ting.

11. Stop operation immediately if you notice any-

thing abnormal.

12. Do not attempt to lock the trigger in the “ON”

position.

13. Never attempt to cut with the tool held upside

down in a vise. This can lead to serious acci-

dents, because it is extremely dangerous. (Fig.

14. Before setting the tool down after completing a

cut, be sure that the wheel has come to a com-

plete stop.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing water pipe (Fig. 2)

First, unplug the tool. Loosen the wing bolt on the depth

guide and move the base down. Install the water pipe on

the blade case using the screw as shown in Fig. 2.

Attach the vinyl tube onto the water pipe and attach the

adapter on the vinyl tube to a faucet of water mains pres-

sure. Adjust the amount of water flow by simply adjusting

the water cock.

Installing or removing diamond wheel

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the wheel.

Hold the outer flange with the wrench and loosen the hex

socket head bolt in clockwise direction with the hex

wrench. Then remove the hex socket head bolt and outer

flange. (Fig. 3)

Install the diamond wheel, outer flange and hex socket

head bolt onto the spindle. Hold the outer flange with the

wrench and tighten the hex socket head bolt in counter-

clockwise direction with the hex wrench. BE SURE TO

TIGHTEN THE HEX SOCKET HEAD BOLT SECURELY.

(Fig. 4)

CAUTION:

Use only the Makita wrench and hex wrench to install or

remove the wheel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 4101 RH Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info