Bedienungsanleitung Makita 4157 KB (Seite 6 von 13) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448194

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

ENGLISH

Explanation of general view

1 Dust box

2 Screw

3 Hex wrench

4 Shaft lock

5 Tighten

6 Loosen

7 Hex socket head bolt

8 Outer flange

9 Diamond wheel

10 Inner flange

11 Lever

12 Bevel scale plate

13 Knob

14 Base

15 Adjusting screw

16 Triangular rule

17 Notch

18 For 45° bevel cuts

19 For straight cuts

20 Switch trigger

21 Lock-off button

22 Rear handle

23 Front grip

24 Guide rule

25 Dust cap

26 Rubber cap

27 Limit mark

28 Brush holder cap

29 Screwdriver

SPECIFICATIONS

Model 4157KB

Wheel diameter ...................................................180 mm

Max. cutting capacities

At 90° ................................................................. 58 mm

At 45° ................................................................. 29 mm

No load speed (min

–1

) ............................................ 5,800

Overall length ..................................................... 354 mm

Net weight ............................................................. 5.5 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

For public low-voltage distribution systems of

between 220V and 250V

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under unfavor-

able mains conditions can have adverse effects to the

operation of other equipment. With a mains impedance

equal or less than 0.31 Ohms it can be presumed that

there will be no negative effects. The mains socket used

for this device must be protected with a fuse or protective

circuit breaker having slow tripping characteristics.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

ENB051-1

1. Check the wheel carefully for cracks or damage

before operation. Replace cracked or damaged

wheel immediately.

2. Use only flanges specified for this tool.

3. Be careful not to damage the spindle, flanges

(especially the installing surface) or bolt. Dam-

age to these parts could result in wheel break-

age.

4. Hold the tool firmly.

5. Keep hands away from rotating parts.

6. Make sure the wheel is not contacting the work-

piece before the switch is turned on.

7. Wait until the wheel attains full speed before cut-

ting.

8. Stop operation immediately if you notice any-

thing abnormal.

9. Do not attempt to lock the trigger in the “ON”

position.

10. Never attempt to cut with the tool held upside

down in a vise. This can lead to serious acci-

dents, because it is extremely dangerous.

(Fig. 1)

11. Before setting the tool down after completing a

cut, be sure that the wheel has come to a com-

plete stop.

12. Do not stop the wheel by lateral pressure on the

disc.

13. The tool must be used only for dry cutting. Do

not use water.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Removing or installing diamond wheel

(Fig. 2, 3 & 4)

CAUTION:

Always be sure that the tool is switched off and

unplugged before removing or installing the wheel.

Use a screwdriver to loosen the two screws which secure

the dust box. Then remove the dust box from the tool.

After removing the dust box, press the shaft lock so that

the diamond wheel cannot revolve and use the hex

wrench to loosen the hex socket head bolt counterclock-

wise. Then remove the hex socket head bolt, outer flange

and the diamond wheel. To install the diamond wheel, fol-

low the removal procedure in reverse.

BE SURE TO TIGHTEN THE HEX SOCKET HEAD

BOLT SECURELY.

CAUTION:

• Make sure that the arrow on the wheel should point in

the same direction as the arrow on the tool.

• Use only the Makita hex wrench to install or remove the

wheel.

Adjusting depth of cut (Fig. 5)

Loosen the lever on the depth guide and move the base

up or down. At the desired depth of cut, secure the base

by tightening the lever.

Bevel cutting (Fig. 6)

Loosen the knob on the bevel scale plate on the front of

the base. Set for the desired angle (0 – 45°) by tilting

accordingly, then tighten the knob securely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 4157 KB Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info