Bedienungsanleitung Makita 4324k (Seite 7 von 19) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch)

382524

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

OPERATING INSTRUCTIONS

Installing or removing saw blade (Fig. 1 & 2)

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing the blade.

• Always clean out all chips or foreign matter adhering to

the blade and/or blade holder. Failure to do so may

cause insufficient tightening of the blade, resulting in a

serious injury.

To install the blade, loosen the bolt on the blade holder

with the hex wrench. With the blade teeth facing forward,

insert the blade into the blade holder as far as it will go.

Make sure that the back edge of the blade fits into the

roller. Then tighten the bolt to secure the blade.

To remove the blade, follow the installation procedures in

reverse.

NOTE:

Occasionally lubricate the roller.

Hex wrench storage (Fig. 3)

When not in use, the hex wrench can be conveniently

stored as shown in Fig. 3.

Dust cover (Fig. 4)

CAUTION:

Always wear safety goggles even when operating the tool

with the dust cover lowered.

Lower the dust cover to prevent chips from flying. How-

ever, when making bevel cuts, raise it all the way.

Switch action (Fig. 5)

CAUTION:

Before plugging in the tooltool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

Selecting the cutting action (Fig. 6)

This tool can be operated with an orbital or a straight line (up and down) cutting action. The orbital cutting action

thrusts the blade forward on the cutting stroke and greatly increases cutting speed.

To change the cutting action, just turn the cutting action changing lever to the desired cutting action position. Refer to

the table below to select the cutting action.

Speed adjusting dial (Fig. 7)

The tool speed can be infinitely adjusted between 500

and 3,100 strokes per minute by turning the adjusting

dial. Higher speed is obtained when the dial is turned in

the direction of number 6; lower speed is obtained when

it is turned in the direction of number 1. Refer to the table

below to select the proper speed for the workpiece to be

cut. However, the appropriate speed may differ with the

type or thickness of the workpiece. In general, higher

speeds will allow you to cut workpieces faster but the ser-

vice life of the blade will be reduced.

CAUTION:

The speed adjusting dial can be turned only as far as 6

and back to 1. Do not force it past 6 or 1, or the speed

adjusting function may no longer work.

Operation (Fig. 8)

CAUTION:

Always hold the tool base flush with the workpiece. Fail-

ure to do so may cause blade breakage, resulting in a

serious injury.

Turn the tool on and wait until the blade attains full speed.

Then rest the tool base flat on the workpiece and gently

move the tool forward along the previously marked cut-

ting line. When cutting curves, advance the tool very

slowly.

Bevel cutting

CAUTION:

• Always be sure that the tool is switched off and

unplugged before tilting the tool base.

• Raise the dust cover all the way before making bevel

cuts.

With the tool base tilted, you can make bevel cuts at any

angle between 0° and 45° (left or right). (Fig. 9)

Loosen the bolt on the back of the tool base with the hex

wrench. Move the tool base so that the bolt is positioned

in the center of the cross-shaped slot in the tool base.

(Fig. 10)

Tilt the tool base until the desired bevel angle is obtained.

The edge of the motor housing indicates the bevel angle.

Check the contact between the back edge of the blade

and the roller, then tighten the bolt to secure the tool

base. (Fig. 11)

Position Cutting action Applications

O Straight line cutting action

For cutting mild steel, stainless steel and plastics.

For clean cuts in wood and plywood.

I Small orbit cutting action For cutting mild steel, aluminum and hard wood.

II Medium orbit cutting action

For cutting wood and plywood.

For fast cutting in aluminum and mild steel.

III Large orbit cutting action For fast cutting in wood and plywood.

Workpiece to be cut Number on adjusting dial

Wood 5–6

Mild steel 3 – 6

Stainless steel 3 – 4

Aluminum 3 – 6

Plastics 1–4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 4324k Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info