Bedienungsanleitung Makita 4331 dwde (Seite 6 von 12) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch)

382497

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ADDITIONAL SAFETY RULES FOR TOOL

ENB030-1

1. Be aware that this tool is always in an operating

condition, because it does not have to be

plugged into an electrical outlet.

2. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring. Contact with a “live”

wire will make exposed metal parts of the tool

“live” and shock the operator.

3. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

4. Do not cut hollow pipe.

5. Do not cut oversize workpiece.

6. Check for the proper clearance beneath the

workpiece before cutting so that the blade will

not strike the floor, workbench, etc.

7. Hold the tool firmly.

8. Check the blade is not contacting the workpiece

before the switch is turned on.

9. Keep hands away from moving parts.

10. Do not leave the tool running. Operate the tool

only when hand-held.

11. Always switch off and wait for the blade to come

to a complete stop before removing the blade

from the workpiece.

12. Do not touch the blade or the workpiece immedi-

ately after operation; they may be extremely hot

and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig.1)

• Always switch off the tool before insertion or removal of the battery cartridge.

• To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge.

• To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into

place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool,

causing injury to you or someone around you.

• Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted

correctly.

Installing or removing saw blade (Fig. 2 &3)

CAUTION:

• Always be sure that the tool is switched off and unplugged before installing or removing the blade.

• Always clean out all chips or foreign matter adhering to the blade and/or blade holder. Failure to do so may cause

insufficient tightening of the blade, resulting in a serious injury.

• Use a lubricant or cutting oil between the blade and roller when cutting iron or composition board, etc. Failure to do

so will shorten the service life of your blade and roller or lead to potentially dangerous blade breakage.

To install the blade, loosen the bolt on the blade holder with the hex wrench. With the blade teeth facing forward, insert

the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits into the roller. Then

tighten the bolt to secure the blade.

To remove the blade, follow the installation procedures in reverse.

NOTE:

Occasionally lubricate the roller.

Installing universal shank jig saw blade (Fig.4 & 5)

CAUTION:

Always be sure that the tool is switched off and unplugged before installing or removing the blade.

If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one

shown in the figure, with a blade width of 6.35mm. Insert the blade into the blade holder as far as it will go. Make sure

that the end of the blade shank reaches the bottom of the inner slit and tighten the bolt securely with the hex wrench.

Selecting the cutting action (Fig. 6)

This tool can be operated with an orbital or a straight line (up and down) cutting action. The orbital cutting action

thrusts the blade forward on the cutting stroke and greatly increases cutting speed.

To change the cutting action, just turn the lever to the desired cutting action position. Refer to the table below to select

the cutting action.

Position Cutting action Applications

Straight line cutting action For cutting mild steel, stainless steel and plastics.

For clean cuts in wood and plywood.

I Small orbit cutting action For cutting mild steel, aluminum and hard wood.

Medium orbit cutting action For cutting wood and plywood.

For fast cutting in aluminum and mild steel.

III Large orbit cutting action For fast cutting in wood and plywood.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 4331 dwde Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info