Bedienungsanleitung Makita 4333 dwde (Seite 7 von 12) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch)

382498

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Switch action (Fig.7)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the “OFF” position when released. Pulling the

trigger hard when the lock-off button is not pressed

causes switch damage.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided. To start the tool,

depress the lock-off button and pull the switch trigger.

Release the switch trigger to stop.

Speed adjusting dial (Fig. 7)

The tool speed can be infinitely adjusted between 500

and 2,800 (Model 4331D), 500 and 2,600 (Model 4333D)

strokes per minute by turning the adjusting dial. Higher

speed is obtained when the dial is turned in the direction

of number 5; lower speed is obtained when it is turned in

the direction of number 1. Refer to the table below to

select the proper speed for the workpiece to be cut. How-

ever, the appropriate speed may differ with the type or

thickness of the workpiece. In general, higher speeds will

allow you to cut workpieces faster but the service life of

the blade will be reduced.

CAUTION:

The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

Operation (Fig. 8)

CAUTION:

• Check carefully that the blade is adequately secured in

position before inserting the battery into the tool.

• Always hold the base flush with the workpiece. Failure

to do so may cause blade breakage, resulting in a seri-

ous injury.

Turn the tool on and wait until the blade attains full speed.

Then rest the base flat on the workpiece and gently move

the tool forward along the previously marked cutting line.

When cutting curves, advance the tool slowly.

Bevel cutting (Fig.9 & 10)

CAUTION:

Always remove the battery from the tool before making

any adjustments.

With the base tilted, you can make bevel cuts at any

angle between 0° and 45° (left or right).

Loosen the bolt on the back of the base with the hex

wrench. Move the base so that the bolt is positioned in

the center of the cross-shaped slot in the base. Tilt the

base until the desired bevel angle is obtained. The edge

of the motor housing indicates the bevel angle by gradua-

tions. Check the contact between the back edge of the

blade and the roller, then tighten the bolt to secure the

base.

Front flush cuts (Fig.11)

Loosen the bolt on the back of the base with the hex

wrench, then move the base all the way back. Then

tighten the bolt to secure the base.

Cutouts (Fig. 12 & 13)

Cutouts can be made with either of two methods A or B.

A) Boring a starting hole: For internal cutouts without a

lead-in cut from an edge, pre-drill a starting hole

more than 12 mm in diameter. Insert the blade into

this hole to start your cut.

B) Plunge cutting: You need not bore a starting hole or

make a lead-in cut if you carefully do as follows.

1. Tilt the tool up on the front edge of the base, with

the blade point positioned just above the work-

piece surface.

2. Apply pressure to the tool so that the front edge of

the base will not move when you switch on the

tool and gently lower the back end of the tool

slowly.

3. As the blade pierces the workpiece, slowly lower

the base of the tool down onto the workpiece sur-

face.

4. Complete the cut in the normal manner.

Finishing edges (Fig. 14)

To trim edges or make dimensional adjustments, run the

blade lightly along the cut edges.

Metal cutting

Always use a suitable coolant (cutting oil) when cutting

metal. Failure to do so will cause significant blade wear.

The underside of the workpiece can be greased instead

of using a coolant.

Anti-splintering device (Fig.15)

To reduce the potential for workpiece surface splintering,

the anti-splintering device can be used. Fit it into the

base from below so that it surrounds the sides of the

blade.

Workpiece to be cut

Number

on adjusting dial

Wood 3 – 5

Mild steel 3 – 5

Stainless steel 3 – 4

Aluminum 2 – 3

Plastics 1 – 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 4333 dwde Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info