Bedienungsanleitung Makita 4334dwd (Seite 9 von 21) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch)

383618

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

Speed adjusting dial (Fig. 4)

The tool speed can be adjusted and maintained between

500 and 2,800 strokes per minute by turning the adjust-

ing dial. The dial is marked 1 (lowest speed) to 5 (full

speed).

Refer to the table below to select the proper speed for the

workpiece to be cut. However, the appropriate speed

may differ with the type or thickness of the workpiece. In

general, higher speeds will allow you to cut workpieces

faster but the service life of the blade will be reduced.

CAUTION:

Adjust the speed adjusting dial only within the range of

numbers 1 through 5. Do not force the dial beyond this

range or damage to the tool may result.

Anti-splintering device (Fig. 5)

To reduce the potential for workpiece surface splintering,

the anti-splintering device can be used. Fit it into the

base from below so that it surrounds the sides of the

blade.

Plastic base plate (optional accessory) (Fig. 6)

Use the plastic base plate when cutting decorative

veneers, plastics, etc. It protects sensitive or delicate sur-

faces from damage. To replace the base plate, remove

the four screws.

Guide rule (rip fence; optional accessory) (Fig. 7)

When cutting widths of under 150 mm repeatedly, use of

the guide rule will assure fast, clean, straight cuts. To

install it, loosen the bolt on the front of the base. Slip in

the guide rule and secure the bolt.

Circular guide (optional accessory) (Fig. 8)

Use of the circular guide insures clean, smooth cutting of

circles (radius: under 200 mm). Insert the pin through the

center hole and secure it with the threaded knob. Move

the base of the tool forward fully. Then install the circular

guide on the base in the same manner as the guide rule.

Vacuum head (optional accessory) (Fig. 9 & 10)

The vacuum head is recommended to perform clean cut-

ting operations. Install the plastic cover on the tool by fit-

ting it into the notches in the tool.

To attach the vacuum head on the tool, insert the hook of

the vacuum head into the hole in the base. The vacuum

head can be installed on either left or right side of the

base. Then connect a Makita vacuum cleaner to the vac-

uum head.

Installing or removing the saw blade

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before installing or removing

the blade.

• Always clean off the blade and blade holder before

installing the blade. Chips or foreign matter on them

may cause insufficient securing of the blade, possibly

resulting in blade breakage or serious injury.

Installation

1. Push the blade installing lever in the (1) direction to

release it. (Fig. 11)

2. Pull the blade installing lever in the (2) direction until

it stops with a little click. If you have difficulty pulling

it out, try to do so while moving it back and forth in

the (3) direction.

3. Rotate the blade installing lever in the (4) direction

until the clamp protrudes 5 – 7 mm from the blade

holder. (Fig. 12)

CAUTION:

If you rotate the blade installing lever excessively, the

clamp will also rotate and finally come off. In this

case, re-install it properly as lately described in

“Installing clamp”.

4. With the blade teeth facing forward, insert the blade

into the blade holder as far as it will go. Make sure

that the back edge of the blade fits properly into the

groove of the roller. (Fig. 13)

5. With the blade held against the blade holder, rotate

the blade installing lever in the (5) direction until it

stops. (Fig. 14)

6. With the blade installing lever held in this position,

push it in the (6) direction. Then rotate the blade

installing lever to its original position. (Fig. 15)

Removal

1. Push the blade installing lever in the (1) direction to

release it. (Fig. 16)

2. Pull the blade installing lever in the (2) direction until

it stops with a little click. If you have difficulty pulling

it out, try to do so while moving it back and forth in

the (3) direction.

3. Rotate the blade installing lever in the (4) direction

and remove the blade. (Fig. 17)

4. Rotate the blade installing lever in the (5) direction

until it stops. (Fig. 18)

5. With the blade installing lever held in this position,

push it in the (6) direction. Then rotate the blade

installing lever to its original position. (Fig. 19)

OPERATION

Cutting operation

CAUTION:

• Always hold the tool with the base flush with the work-

piece. Failure to do so may cause a slanted cutting sur-

face and blade breakage.

• Advance the tool very slowly when cutting curves or

scrolling. Forcing the tool may cause a slanted cutting

surface and blade breakage.

Turn the tool on without the blade making any contact.

Rest the base flat on the workpiece and gently move the

tool forward along the previously marked cutting line.

(Fig. 20)

Workpiece to be cut Number on adjusting dial

Wood 3 – 5

Mild steel 3 – 5

Stainless steel 3 – 4

Aluminum 2 – 3

Plastics 1 – 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 4334dwd Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info