Bedienungsanleitung Makita 4390D (Seite 5 von 24) (Englisch, Französisch, Spanisch)

690959

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

• Always switch off the tool before insertion or

removal of the battery cartridge.

• To remove the battery cartridge, pull out the set

plate on the tool and grasp both sides of the

cartridge while withdrawing it from the tool.

• To insert the battery cartridge, align the tongue on

the battery cartridge with the groove in the housing

and slip it into place. Snap the set plate back into

place. Be sure to close the set plate fully before

using the tool to prevent the battery cartridge from

accidentally falling out of the tool.

• Do not use force when inserting the battery

cartridge. If the cartridge does not slide in easily, it

is not being inserted correctly.

Switch action

002490

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger

actuates properly and returns to the "OFF" position

when released.

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided.

To start the tool, slide the lock-off lever in the direction of

the arrow and pull the switch trigger. Release the switch

trigger to stop.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out

any work on the tool.

Installing or removing the saw blade

002498

CAUTION:

• Always clean out all chips or foreign matter

adhering to the blade, blade clamp and/or slider.

Failure to do so may cause insufficient tightening

of the blade, resulting in a serious injury.

To install the blade, loosen the bolt on the blade clamp

with the hex wrench. Keep the back edge of the blade

against the roller and insert the blade between the blade

clamp and the slider as far as it will go. Make sure that

you are inserting the blade into the proper position.

Fit the pin on the slider into the hole in the blade shank.

002499

NOTE:

• The hole in the blade shank will be aligned with the

pin on the slider when the blade shank hits against

the spring pin on the slider.

After the pin fits properly into the hole, tighten the bolt

clockwise securely while making sure that the blade

cannot be extracted even though you try to pull it out.

002500

CAUTION:

• If you tighten the bolt without the pin on the slider

fitting properly in the hole in the blade shank, the

pin or the blade shank will be damaged. This may

cause the blade to be extracted unexpectedly

during operation.

To remove the blade, follow the installation procedure in

reverse.

1. Slider

2. Hex wrench

3. Roller

4. Blade

5. Blade clamp

6. Shoe

1. Blade clamp

2. Slider

3. Spring pin

4. Pin

5. Blade shank

6. Hole

1. Roller

2. Blade clamp

3. Blade installing

position

1. Lock-off lever

2. Switch trigger

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 4390D Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info