Bedienungsanleitung Makita 5103r (Seite 8 von 13) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

382525

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

17. Never attempt to saw with the circular saw

held upside down in a vise. This is extremely

dangerous and can lead to serious accidents.

Fig. G

18. Before setting the tool down after completing

a cut, be sure that the lower (telescoping)

guard has closed and the blade has come to a

complete stop.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Removing or installing saw blade

The following blade can be used with this tool.

Model Max. dia. Min. dia. Blade thickness Kerf

5603R 165 mm 150 mm 1.6 mm or less 1.9 mm or more

5703R 190 mm 170 mm 1.6 mm or less 1.9 mm or more

5903R 235 mm 210 mm 1.7 mm or less 2.1 mm or more

5103R 270 mm 260 mm 1.8 mm or less 2.2 mm or more

5143R 355 mm 350 mm 2.3 mm or less 2.7 mm or more

The thickness of the riving knife is 1.8 mm for Models

5603R and 5703R or 2.0 mm for Models for 5903R

and 5103R or 2.5 mm for Model 5143R.

CAUTION:

•

Do not use saw blades which do not comply with the

characteristics specified in these instructions.

•

Do not use saw blades the disc of which is thicker or

the set of which is smaller than the thickness of the

riving knife.

To remove the saw blade, depress the shaft lock fully

to prevent shaft rotation, then use the hex wrench to

loosen the hex socket head bolt. (Fig. 1)

Now remove the outer flange, raise the safety cover

as much as possible, and remove the saw blade.

(Fig. 2)

Install the saw blade using the reverse of the removal

procedure. Install the inner flange, saw blade, outer

flange and hex socket head bolt, in that order. Be sure

to secure the hex socket head bolt tightly with the

shaft lock fully depressed. (Fig.1&3)

CAUTION:

•

Make sure that the blade teeth point forward in the

same direction as the tool rotation (the arrow on the

blade should point in the same direction as the

arrow on the tool).

•

Never depress the shaft lock while the saw is

running.

•

Use only the Makita socket wrench to remove or

install the blade.

Riving knife adjustment (Fig. 4)

Use the socket wrench to loosen the hex head socket

bolt for the riving knife adjustment, then raise the

safety cover. Move the riving knife up or down over

the two protuberances for settings indicated in the

illustration, so as to obtain the proper clearance

between the riving knife and saw blade.

CAUTION:

Ensure that the riving knife is adjusted such that:

The distance between the riving knife and the toothed

rim of the saw blade is not more than 5 mm.

The toothed rim does not extend more than 5 mm

beyond the lower edge of the riving knife.

Adjusting depth of cut (Fig. 5)

Loosen the lever on the depth guide and move the

base up or down. At a desired depth of cut, secure the

base by tightening the lever.

CAUTION:

•

Use a shallow depth of cut when cutting thin work-

piece for cleaner, safer cuts.

•

After adjusting the depth of cut, always tighten the

lever securely.

5603R – 5413R (E) (’99. 6. 14)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 5103r Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info