Bedienungsanleitung Makita 5705 (Seite 5 von 13) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

110248

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

ENGLISH

Explanation of general view

1 Hex wrench

2 Shaft lock

3 Tighten

4 Loosen

5 Saw blade

6 Outer flange

7 Inner flange

8 Outer flange

9 Hex socket head bolt

0 Saw blade

q Setting protuberances

w Hex socket head bolt

(For adjusting riving knife)

e Cutting depth

r Loosen

t Lever

y Thumb nut

u For 45° bevel cuts

i For straight cuts

o Base plate

p 45° angle cuts

a Straight cuts

s Top guide

d Base

f Lock-off button

g Switch trigger

h Vacuum cleaner

j Limit mark

k Brush holder cap

l Screwdriver

SPECIFICATIONS

Model 5603R 5705R 5903R

Blade diameter ..................................................................... 165 mm 190 mm 235 mm

Max. cutting depth

At 90° ................................................................................ 54 mm 66 mm 85 mm

At 45° ................................................................................ 38 mm 46 mm 64 mm

No load speed (min

–1

) ......................................................... 5,000 4,800 4,500

Overall length ....................................................................... 330 mm 356 mm 400 mm

Net weight ............................................................................ 4.2 kg 5.2 kg 7.6 kg

•

Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

•

Note: Specifications may differ from country to

country.

Power supply

The tool should be connected only to a power supply

of the same voltage as indicated on the nameplate,

and can only be operated on single-phase AC supply.

They are double-insulated in accordance with Euro-

pean Standard and can, therefore, also be used from

sockets without earth wire.

For model 5705R, public low-voltage distribution

systems of between 220 V and 250 V

Switching operations of electric apparatus cause volt-

age fluctuations. The operation of this device under

unfavorable mains conditions can have adverse

effects to the operation of other equipment. With a

mains impedance equal or less than 0.36 Ohms it can

be presumed that there will be no negative effects.

The mains socket used for this device must be

protected with a fuse or protective circuit breaker

having slow tripping characteristics.

Safety hints

For your own safety, please refer to the enclosed

Safety instructions.

ADDITIONAL SAFETY RULES FOR

TOOL

ENB036-2

1. Wear hearing protection.

2. Keep Guards In Place and In Working Order.

Never wedge or tie lower guard open. Check

operation of lower guard before each use.

Don’t use if lower guard does not close briskly

over saw blade.

CAUTION: If saw is dropped, lower guard may

be bent, restricting full return.

3. Do not use blades which are deformed or

cracked.

4. Do not use blades made of high speed steel.

5. Do not stop the blades by lateral pressure on

the saw blade.

6. Keep Blades Clean and Sharp.

Sharp blades minimize stalling and kickback.

7. DANGER: Keep Hands Away From Cutting

Area. Keep hands away from blades. Don’t

reach underneath work while blade is rotating.

Don’t attempt to remove cut material when

blade is moving.

CAUTION: Blades coast after turn off.

8. Support Large Panels. (Fig. A & B)

Large panels must be supported as shown in

Fig. A to minimize the risk of blade pinching

and kickback.

When cutting operation requires the resting of

the saw on the workpiece, the saw shall be

rested on the larger portion and the smaller

piece cut off.

To avoid kickback, do support board or panel

near the cut.

Fig. A

5603R-y2k (E) (’100. 10. 10)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 5705 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info