Bedienungsanleitung Makita 6409 (Seite 4 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

690966

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

ENGLISH

Explanation of general view

1Chuck

2 Chuck key

3 Tighten

4Sleeve

5 Ring

6 Switch trigger

7 Lock button

8 Reversing switch lever

SPECIFICATIONS

Model 6409 6410

Drilling capacities

Steel ......................................................................................... 10 mm 10 mm

Wood ........................................................................................25 mm 25 mm

No load speed (min

–1

) ................................................................. 2,200 0 – 2,200

Overall length .............................................................................. 248 mm 248 mm

Net weight ................................................................................... 1.2 kg 1.2 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

2. Hold the tool firmly.

3. Keep hands away from rotating parts.

4. When drilling into walls, floors or wherever

“live” electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE TOOL!

Hold the tool by the insulated grasping surfaces

to prevent electric shock if you drill into a “live”

wire.

5. Do not leave the tool running. Operate the tool

only when hand-held.

6. Do not touch the drill bit or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing drill bit

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

For 6409 (Fig. 1)

To install the bit, place it in the chuck as far as it will go.

Tighten the chuck by hand. Place the chuck key in each

of the three holes and tighten clockwise. Be sure to

tighten all three chuck holes evenly.

To remove the bit, turn the chuck key counterclockwise in

just one hole, then loosen the chuck by hand.

After using the chuck key, remember to return it to the

chuck key holder.

For 6410 (Fig. 2)

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far as

it will go. Hold the ring firmly and turn the sleeve clock-

wise to tighten the chuck.

To remove the bit, hold the ring and turn the sleeve coun-

terclockwise.

Switch action (Fig. 3)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

For 6409

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

For 6410

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop. For continuous operation, pull the trig-

ger and then push in the lock button. To stop the tool from

the locked position, pull the trigger fully, then release it.

Reversing switch action (Fig. 4)

For 6410

CAUTION:

• Always check the direction of rotation before drilling.

• Use the reversing switch lever only after the tool comes

to a complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

This tool has a reversing switch to change the direction of

rotation. Move the reversing switch lever to

the

d position for clockwise rotation or the e position

for counterclockwise rotation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 6409 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info