Bedienungsanleitung Makita 6413 (Seite 4 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch)

78740

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Reversing switch action (Fig. 4)

For 6412, 6413

This tool has a reversing switch to change the direction of

rotation. Move the reversing switch lever to

the

D position (A side) for clockwise rotation or the

E position (B side) for counterclockwise rotation.

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

Holding the tool

Hold the tool only by the handle when performing an

operation.

Drilling operation

Drilling in wood

When drilling in wood, best results are obtained with

wood drills equipped with a guide screw. The guide

screw makes drilling easier by pulling the bit into the

workpiece.

Drilling in metal

To prevent the bit from slipping when starting a hole,

make an indentation with a center-punch and hammer at

the point to be drilled. Place the point of the bit in the

indentation and start drilling.

Use a cutting lubricant when drilling metals. The excep-

tions are iron and brass which should be drilled dry.

CAUTION:

• Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool perfor-

mance and shorten the service life of the tool.

• There is a tremendous force exerted on the tool/bit at

the time of hole break through. Hold the tool firmly and

exert care when the bit begins to break through the

workpiece.

• Always secure small workpieces in a vise or similar

hold-down device.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Drill bits

ENG102-3

For Model 6412, 6413

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (

): 82 dB (A)

Sound power level (

): 93 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

ENG201-2

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: Driling into metal

Vibration emission (

h, D

): 3.5 m/s

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been mea-

sured in accordance with the standard test method and

may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the oper-

ator that are based on an estimation of exposure in the

actual conditions of use (taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to

the trigger time).

ENH101-13

For European countries only

EC Declaration of Conformity

We Makita Corporation as the responsible

manufacturer declare that the following Makita

machine(s):

Designation of Machine:

Drill

Model No./ Type: 6412, 6413

are of series production and

Conforms to the following European Directives:

98/37/EC until 28th December 2009 and then with

2006/42/EC from 29th December 2009

And are manufactured in accordance with the following

standards or standardised documents:

EN60745

The technical documentation is kept by our authorised

representative in Europe who is:

Makita International Europe Ltd.

Michigan Drive, Tongwell,

Milton Keynes, MK15 8JD, England

30th January 2009

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 6413 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info