Bedienungsanleitung Makita 6802 (Seite 3 von 12) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

78953

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

Explanation of general view

1 Locking position

2 Locator

3 Locking sleeve

4 Magnetic socket bit

5 Gear housing

6 Socket bit

7Low

8 High

9 Speed control screw

10 Switch trigger

11 Lock button

12 Reversing switch lever

13 Insert bit

14 Magnetic bit holder

SPECIFICATIONS

Model 6802BV

Capacities

Self drilling screw ...........................................6 mm

Bit shank size ............................................... 1/4” Hex

No load speed (min

-1

) ................................0 – 2,500

Overall length ................................................265 mm

Net weight ........................................................1.7 kg

• Due to our continuing program of research and

development, the specifications herein are subject

to change without notice.

• Note: Specifications may differ from country to

country.

Power supply

The tool should be connected only to a power supply

of the same voltage as indicated on the nameplate,

and can only be operated on single-phase AC supply.

They are double-insulated in accordance with Euro-

pean Standard and can, therefore, also be used from

sockets without earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

SPECIFIC SAFETY RULES

GEB017-1

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict

adherence to screwdriver safety rules. If you use

this tool unsafely or incorrectly, you can suffer

serious personal injury.

1. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

3. Hold the tool firmly.

4. Keep hands away from rotating parts.

5. Do not touch the bit or the workpiece immedi-

ately after operation; they may be extremely hot

and could burn your skin.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious

personal injury.

OPERATING INSTRUCTIONS

Removing or installing locator assembly

(Fig. 1)

To remove the locator assembly, pull the locking

sleeve forward and then turn it counterclockwise. To

install the locator assembly, screw it clockwise and

then push the locking sleeve back in lightly toward

the motor. Turn the locking sleeve slightly to match

the locking positions and then push in firmly to lock

the locator in place.

Removing or installing magnetic socket bit

(Fig. 2)

Important:

Always be sure that the tool is switched off and

unplugged before removing or installing the bit.

After removing the locator assembly, pull firmly to

remove the magnetic socket bit. To install the bit,

insert it into the tool as far as it will go.

Depth adjustment (Fig. 3 & 4)

Pull the locking sleeve forward and then turn it to

adjust the depth.

Initially, adjust the locator assembly to create a dis-

tance of approximately 0.5 mm from the tip of the

locator to the tip of the socket bit. One full turn of the

locator equals 1.5 mm change in depth. After adjust-

ing the locator assembly, push the locking sleeve in to

lock the locator in place. Drive a trial screw into your

material or a piece of duplicate material. If the depth

is not suitable for the screw, continue adjusting until

the proper depth setting is obtained.

Switch action (Fig. 5)

CAUTION:

Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the trigger. tool speed is

increased by increasing pressure on the trigger.

Release the trigger to stop. For continuous operation,

pull the trigger and then push in the lock button. To

stop the tool from the locked position, pull the trigger

fully, then release it. A speed control screw is pro-

vided so that maximum tool speed can be limited

(variable). Turn the speed control screw clockwise for

higher speed, and counterclockwise for lower speed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 6802 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info