Bedienungsanleitung Makita 6802bv (Seite 3 von 32) (Deutsch)

381155

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ENGLISH

Explanation of general view

1 Locking position

2 Locator

3 Locking sleeve

4 Magnetic socket bit

5 Gear housing

6 Socket bit

7 Low

8 High

9 Speed control screw

0 Switch trigger

q Lock button

w Reversing switch lever

e Insert bit

r Magnetic bit holder

SPECIFICATIONS

Capacities

Self drilling screw .......................................... 6 mm

Bit shank size ............................................. 1/4’’ Hex

No load speed (RPM) ................................ 0 – 2,500

Overall length ............................................... 265 mm

Net weight ....................................................... 1.7 kg

•

Due to the continuing program of research and

development, the specifications herein are subject

to change without prior notice.

•

Note: Specifications may differ from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, and can only be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

These symbols mean:

Read instruction manual.

DOUBLE INSULATION

ADDITIONAL SAFETY RULES

1. Always be sure you have a firm footing.

Be sure no one is below when using the

machine in high locations.

2. Hold the machine firmly.

3. Keep hands away from rotating parts.

4. When driving into walls, floors or wherever

‘‘live’’ electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE

MACHINE!

Hold the machine by the insulated grasping

surfaces to prevent electric shock if you drive

into a ‘‘live’’ wire.

5. Do not touch the bit or the workpiece immedi-

ately after operation; they may be extremely

hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Removing or installing locator assembly

(Fig. 1)

To remove the locator assembly, pull the locking

sleeve forward and then turn it counterclockwise. To

install the locator assembly, screw it clockwise and

then push the locking sleeve back in lightly toward the

motor. Turn the locking sleeve slightly to match the

locking positions and then push in firmly to lock the

locator in place.

Removing or installing magnetic socket bit

(Fig. 2)

Important:

Always be sure that the machine is switched off and

unplugged before removing or installing the bit.

After removing the locator assembly, pull firmly to

remove the magnetic socket bit. To install the bit,

insert it into the machine as far as it will go.

Depth adjustment (Fig.3&4)

Pull the locking sleeve forward and then turn it to

adjust the depth.

Initially, adjust the locator assembly to create a dis-

tance of approximately 0.5 mm from the tip of the

locator to the tip of the socket bit. One full turn of the

locator equals 1.5 mm change in depth. After adjust-

ing the locator assembly, push the locking sleeve in to

lock the locator in place. Drive a trial screw into your

material or a piece of duplicate material. If the depth

is not suitable for the screw, continue adjusting until

the proper depth setting is obtained.

Switch action (Fig. 5)

CAUTION:

Before plugging in the machine, always check to see

that the switch trigger actuates properly and returns to

the ‘‘OFF’’ position when released.

To start the machine, simply pull the trigger. Machine

speed is increased by increasing pressure on the

trigger. Release the trigger to stop. For continuous

operation, pull the trigger and then push in the lock

button. To stop the machine from the locked position,

pull the trigger fully, then release it. A speed control

screw is provided so that maximum machine speed

can be limited (variable). Turn the speed control

screw clockwise for higher speed, and counterclock-

wise for lower speed.

NOTE:

Even with the switch on and motor running, the bit will

not rotate until you fit the point of the bit in the screw

head and apply forward pressure to engage the

clutch.

6802BV (Eng) (’96. 2. 29)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 6802bv Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita 6802bv

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info