Bedienungsanleitung Makita 6842 (Seite 6 von 40) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

381597

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Hook (Fig. 3)

The hook is convenient for hooking the tool to your belt. It

can be installed on either side of the tool.

Changing the installation position of hook allows two-way

setting of 10 mm and 20 mm distance from the tool itself.

The tool with hook can be hung on the waist belt, a maxi-

mum diameter 20 mm pipe etc.

To remove the hook, just remove the clamping screw.

Place it on the tool and secure it with the clamping screw

to install.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing the bit (Fig. 4 & 5)

Loosen the thumb screws which secure the casing. Pull

out the casing in the direction of the arrow.

Press the dust cover toward the plain bearing and pull

out the bit. If the dust cover cannot be moved as far as

the plain bearing, try it again after turning the bit slightly.

To install the bit, insert it into the socket while turning it

slightly. After installing, always make sure that the bit is

securely held in place by trying to pull it out.

Setting for desired screw length (Fig. 6)

There are 7 positive-lock screw length settings. To obtain

the desired setting, pull out the stopper base while

depressing the lever until you see the number of the

desired screw length (indicated on the label on feeder

box) appear to rest in the fenestella of stopper base. See

the table below for the relation between the number indi-

cated on the label on feeder box and the respective

screw length.

For Models 6842, 6843

For Model 6844

Adjusting the driving depth (Fig. 7)

Depress the stopper base as far as it will go. While keep-

ing it in this position, turn the adjusting knob until the bit

tip projects approx. 5 mm from the stopper base. Drive a

trial screw. If the screw head projects above the surface

of the workpiece, turn the adjusting knob in the “A” direc-

tion; if the screw head is counter-sunk, turn the adjusting

knob in the “B” direction.

Installing screw strip (Fig. 8 & 9)

Insert the screw strip through the screw guide. Then

insert it through the feeder box until the first screw

reaches the position next to the driving position.

Removing screw strip (Fig. 10 & 11)

To remove the screw strip, just pull it out in the direction

of the arrow. If you depress the reverse button, you can

pull out the screw strip in the reverse direction of the

arrow.

Folding screw guide (Fig. 12)

Screw guide is foldable. Folding the screw guide allows

space used for storage to be minimal.

Extension handle (optional accessory) (Fig. 13)

Use of extension handle allows you to drive screws into

floors while standing.

OPERATION

Driving operation (Fig. 14)

Switch on the tool by pressing the switch trigger and at

the same time pushing the lock button. Hold the tool

squarely against the workpiece and apply forward pres-

sure to the tool. The screw will be automatically carried to

the driving position and driven into the workpiece.

CAUTION:

• Always hold the tool squarely against the driving sur-

face. Holding it at an angle may damage the screw

heads and cause wear on the bit. This may also lead to

poor fastening.

• Always keep the tool firmly against the driving surface

until the driving is over. Failure to do so may cause

insufficient fastening of screws.

• Be careful not to drive a screw onto another screw

already fastened.

• Do not operate the tool without screws. It will damage

the driving surface.

Driving in corner (Fig. 15)

This tool can be used to drive at a position 15 mm away

from the wall as shown in Fig. 15.

CAUTION:

• Driving at a position closer than 15 mm to the wall or

driving with the stopper base in contact with the wall

may damage the screw heads and cause wear on the

bit. This may also lead to poor fastening of screws and

malfunction of the tool.

Number indicated on the label Screw length

25 25 mm

30 30 mm

35 35 mm

40 40 mm

45 45 mm

50 50 mm

55 55 mm

Number indicated on the label Screw length

45 45 mm

50 50 mm

55 55 mm

60 60 mm

65 65 mm

70 70 mm

75 75 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 6842 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info