Bedienungsanleitung Makita 6960D (Seite 3 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

690983

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

Explanation of general view

1 Button

2 Battery cartridge

3 Charging light

4 Fast charger

5 Bit

6 Sleeve

7 Switch trigger

8 Reversing switch lever

9 A side

10 B side

11 Clockwise

12 Counterclockwise

13 Screw

14 Set plate

15 Limit mark

16 Screwdriver

17 Brush holder cap

SPECIFICATIONS

Model 6960D

Capacities

Wood screw ................................. ø3.5 mm – ø9.5 mm

No load speed (min

-1

) ...................................... 0 – 2,500

Impacts per minute .......................................... 0 – 1,600

Fastening torque ................................................. 30 N

Overall length ..................................................... 195 mm

Net weight ............................................................. 1.8 kg

Rated voltage .................................................. D.C. 12 V

•

Due to the continuing program of research and devel-

opment, the specifications herein are subject to change

without prior notice.

•

Note: Specifications may differ from country to country.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

IMPORTANT SAFETY INSTRUCTIONS FOR

CHARGER & BATTERY

CARTRIDGE

ENC001-3

1. SAVE THESE INSTRUCTIONS — This manual

contains important safety and operating instruc-

tions for battery charger.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger,

(2) battery, and (3) product using battery.

3. CAUTION — To reduce risk of injury, charge only

MAKITA type rechargeable batteries. Other types

of batteries may burst causing personal injury

and damage.

4. Do not expose charger to rain or snow.

5. Use of an attachment not recommended or sold

by the battery charger manufacturer may result in

a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and

cord, pull by plug rather than cord when discon-

necting charger.

7. Make sure cord is located so that it will not be

stepped on, tripped over, or otherwise subjected

to damage or stress.

8. Do not operate charger with damaged cord or

plug — replace them immediately.

9. Do not operate charger if it has received a sharp

blow, been dropped, or otherwise damaged in any

way; take it to a qualified serviceman.

10. Do not disassemble charger or battery cartridge;

take it to a qualified serviceman when service or

repair is required. Incorrect reassembly may

result in a risk of electric shock or fire.

11. To reduce risk of electric shock, unplug charger

from outlet before attempting any maintenance or

cleaning. Turning off controls will not reduce this

risk.

12. The battery charger is not intended for use by

young children or infirm persons without super-

vision.

13. Young children should be supervised to ensure

that they do not play with the battery charger.

14. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an explo-

sion.

15. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

ADDITIONAL SAFETY RULES FOR CHARGER

& BATTERY CARTRIDGE

1. Do not charge battery cartridge when temperature

is BELOW 10°C (50°F) or ABOVE 40°C (104°F).

2. Do not attempt to use a step-up transformer, an

engine generator or DC power receptacle.

3. Do not allow anything to cover or clog the charger

vents.

4. Always cover the battery terminals with the bat-

tery cover when the battery cartridge is not used.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop, shake or strike battery.

9. Do not charge inside a box or container of any

kind. The battery must be placed in a well venti-

lated area during charging.

ADDITIONAL SAFETY RULES

FOR TOOL

ENB024-1

1. Be aware that this tool is always in an operating

condition, because it does not have to be plugged

into an electrical outlet.

2. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring. Contact with a ‘‘live’’

wire will also make exposed metal parts of the

tool ‘‘live’’ and shock the operator.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 6960D Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info