690985
5
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
5
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
Intended use
ENE062-1
The tool is intended for cutting mortise in wood.
Power supply
ENF001-1
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. This tool
should be grounded while in use to protect the operator
from electric shock. Use only three-wire extension cords
which have three-prong grounding-type plugs and three-
pole receptacles which accept the tool’s plug.
General Power Tool Safety
Warnings GEA010-1
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
ADDITIONAL SAFETY RULES
ENB093-1
1. Use this tool only to cut holes in wood.
2. This tool is for cutting holes in flat-surfaced wood.
Never use it for cutting holes in a log.
3. Wear ear protectors.
4. Handle the cutter chain carefully; it is very sharp.
5. Place the workpiece on wood blocks or short
beams to prevent the cutter chain from hitting the
ground, floor, etc., causing damage to the cutter
chain at the time of hole breakthrough.
6. Check the cutter chain carefully for cracks or
damage before operation. Replace cracked or
damaged cutter chain immediately.
7. Secure the tool to the workpiece firmly.
8. Inspect for and remove nails or foreign matter
from the workpiece before operation.
9. Do not operate the tool with the safety cover open.
10. Do not wear gloves during operation.
11. Keep hands away from moving parts.
12. Remove the tool from the workpiece after
operation to keep it from falling off and possibly
causing injury.
13. Don’t abuse cord. Never yank cord to disconnect
it from the receptacle. Keep cord away from heat,
oil, water and sharp edges.
14. PROPER GROUNDING. This tool should be
grounding while in use to protect the operator
from electric shock.
1. Wing bolt
2. Stopper pole
3. Stopper
4. Lock-off button
5. Switch trigger
6. Adjusting screw
7. Chain bar
8. Chain cover
9. Hex bolt
10. Arrow
11. Sprocket
12. Lever (A)
13. Vise lever
14. Rear vise
15. Setting handle
16. Front vise
17. Indicator plate
18. Indication plate
19. Cutting line (A)
20. Cutting line (B)
21. Hook
22. Hex bolts
23. Gauge plate
24. Travel distance (D)
25. Lever (B)
26. Lever (C)
27. Adjusting hex bolt for No. 1 set
position
28. Adjusting hex bolt for No. 2 set
position
29. Original position
30. No.1 set position
31. No.2 set position
32. Ruler
33. Front vise
34. Limit mark
35. Brush holder cap
36. Screwdriver
Model 7104L
Capacities
Max. hole length
(Longitudinal)
130 mm
Max. hole depth 155 mm
Width of applicable workpiece 80 mm – 308 mm
Chain speed 300 m/min
Dimensions (L × W × H) 512 mm × 298 mm × 513 mm
Net weight 17.3 kg
Safety class Class I
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita 7104L wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info