Bedienungsanleitung Makita 8406 (Seite 8 von 19) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

387501

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Hammer drilling (with a tungsten-carbide tipped bit)

When drilling in concrete, granite, tile, etc. with a tung-

sten-carbide tipped bit, first use “rotation only” action to

start a hole, then use “rotation with hammering” action to

continue drilling.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the tool at

an idle, then remove from the hole. By repeating this

several times, the hole will be cleaned out.

Drilling (with a conventional drill bit)

When drilling in wood, metal or plastic materials, use

“rotation only” action.

1. Drilling in wood

When drilling in wood, best results are obtained with

wood drills equipped with a guide screw. The guide

screw makes drilling easier by pulling the bit into the

workpiece.

2. Drilling in metal

To prevent the bit from slipping when starting a hole,

make an indentation with a centerpunch and ham-

mer at the point to be drilled. Place the point of the

bit in the indentation and start drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be

drilled dry.

CAUTION:

• Pressing excessively on the tool will not speed up the

drilling. If fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool perfor-

mance and shorten the service life of the tool.

• There is tremendous force exerted on the tool/bit at the

time of hole breakthrogh. Hold the tool firmly and exert

care when the bit begins to break through the work-

piece.

• Always secure small workpieces in a vise or similar

hold-down device.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

Replacing carbon brushes (Fig. 22)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps.

Take out the worn carbon brushes, insert the new ones

and secure the brush holder caps. (Fig. 23)

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized or Factory Service Centers

always using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

Diamond core bit (Dry type)

Diamond core bit

Center bit

Center bit shank

Diamond core bit (Wet type)

Diamond core bit

Sponge

Guide ring

Sheet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 8406 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info