Bedienungsanleitung Makita 9031 (Seite 4 von 12) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

390331

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

Explanation of general view

1 Side grip can be pivoted

2 Side grip

3 Grip holder

4 Rear pulley

5 Front pulley

6Arrow

7 Lock button

8 Switch trigger

9 Speed adjusting dial

10 Nozzle cap

11 Nozzle

12 Vacuum cleaner

13 Limit mark

14 Brush holder cap

15 Screwdriver

SPECIFICATIONS

Model 9031

Belt size................................................ 30 mm x 533 mm

Belt speed ..................................... 200 m – 1,000 m/min.

Overall length ...................................................... 380 mm

Net weight .............................................................. 2.1 kg

• Due to our continuing programme of research and

development, the specifications herein are subject to

change without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed Safety

instructions.

SPECIFIC SAFETY RULES

GEB015-1

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to belt sander safety rules. If you use this tool

unsafely or incorrectly, you can suffer serious per-

sonal injury.

1. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Ventilate your work area adequately when you

perform sanding operations.

3. Some material contains chemicals which may be

toxic. Take caution to prevent working dust inha-

lation and skin contact. Follow material supplier

safety data.

4. Always use the correct dust mask/respirator for

the material and application you are working

with.

5. Always use safety glasses or goggles. Ordinary

eye or sun glasses are NOT safety glasses.

6. Hold the tool firmly with both hands.

7. Make sure the belt is not contacting the work8

piece before the switch is turned on.

8. Keep hands away from rotating parts.

9. Do not leave the tool running. Operate the tool

only when hand-held.

10. This tool has not been waterproofed, so do not

use water on the workpiece surface.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

OPERATING INSTRUCTIONS

Installing side grip (Fig. 1)

For your own safety, always use the side grip. Install it on

the grip holder. The side grip can be pivoted for easy

operation.

Installing or removing abrasive belt (Fig. 2 & 3)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the belt.

Loop the belt over the front pulley. Hold the tool as shown

in Fig. 2 and press down on the front pulley so that you

can slip the other end over the rear pulley.

NOTE:

The arrow on the inside of the belt and that on the rear

pulley must be in the same direction.

Switching ON and OFF (Fig. 4)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To switch on, press the trigger. To switch off, release the

trigger.

Continuous running (Fig. 4)

Press the trigger and at the same time push the lock but-

ton. To stop this lock position, press the trigger and

release it.

Speed adjusting dial (Fig. 5)

The belt running speed can be adjusted between 200 m/min.

and 1,000 m/min. by turning the adjusting dial. The dial is

marked 1 (lowest speed) to 6 (full speed).

Operation

Hold the tool firmly with both hands. Press the belt only

lightly on the workpiece. Excessive pressure may dam-

age the belt and shorten tool life.

Dust extraction (Fig. 6 & 7)

Open the nozzle cap. Connect a hose of vacuum cleaner/

dust collector to the nozzle.

NOTE:

Always close the nozzle cap when the vacuum cleaner/

dust collector is not connected to the nozzle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 9031 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info