448259
6
Zoom out
Zoom in
Vorherige Seite
1/18
Nächste Seite
22. If working placeis extremely hot and humid, or
badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure opera-
tor safety.
23. Do not use the tool on any materials contain-
ing asbestos.
24. Do not use water or grinding lubricant.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing wheel guard (Fig. 1)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the wheel
guard.
When installing a depressed center wheel or an
abrasive cut-off wheel, always use a wheel guard.
Loosen the lever on the wheel guard. Mount the
wheel guard with the protrusion on the wheel guard
band aligned with the notch on the bearing box. Then
rotate the wheel guard 180 degrees clockwise.
Tighten the lever to fasten the wheel guard. If the
lever is too tight or too loose to fasten the wheel
guard, loosen or tighten the screw to adjust the
tightening of the wheel guard band.
Installing side grip (auxiliary handle) (Fig. 2)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the side grip.
Always install the side grip on the tool securely before
operation. The side grip can be installed in any of
three positions on the sides of the tool, whichever is
convenient and keeps the guard properly positioned.
Always hold the tool’s switch handle and the side grip
firmly with both hands during operation.
Shaft lock (Fig. 3)
Press the shaft lock to prevent spindle rotation when
installing or removing accessories.
CAUTION:
Never actuate the shaft lock when the spindle is
moving. The tool may be damaged.
Installing or removing depressed center
wheel (Fig.4&5)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the wheel.
Mount the inner flange onto the spindle. Fit the wheel
on over the inner flange and screw the lock nut onto
the spindle.
To tighten the lock nut, press the shaft lock firmly so
that the spindle cannot revolve, then use the lock nut
wrench and securely tighten clockwise.
To remove the wheel, follow the installation procedure
in reverse.
Switch action (Fig. 6)
CAUTION:
Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
‘‘OFF’ position when released.
For U.K., Australia, New Zealand, France, Réunion
and Algeria
To prevent the trigger from being accidentally actu-
ated, a lock lever is provided. To start the tool, push
the lock lever in the arrow direction and then pull the
trigger. Release the trigger to stop.
For Germany, Austria, Italy, Switzerland,
Netherlands, Belgium, Spain, Portugal, Denmark,
Sweden, Norway, Finland, Greece, Russia and
South Africa
To prevent the trigger from being accidentally actu-
ated, a lock lever is provided. To start the tool, push
the lock lever in the arrow direction and then pull the
trigger. Release the trigger to stop. For continuous
operation, push the lock lever in the arrow direction,
pull the trigger and then push the lock lever further in
the arrow direction. To stop the tool from the locked
position, pull the trigger fully, then release it.
For all other countries
To start the tool, simply pull the trigger. Release the
trigger to stop. For continuous operation, pull the
trigger and then push the lock lever in the arrow
direction. To stop the tool from the locked position,
pull the trigger fully, then release it.
NOTE:
Models 9077S, 9077SL and 9079S begin to run
slowly when they are turned on. This soft start feature
assures smoother operation and less operator
fatigue.
Switch handle mounting positions (Fig. 7)
The switch handle can be rotated to either 90° left or
right to fit your work needs. First, unplug the tool.
Press the lock button and rotate the switch handle
until the n mark on the lock button is aligned with that
on the motor housing. The switch handle will be
locked in that position.
Operation (Fig. 8)
CAUTION:
After operation, always switch off the tool and wait
until the wheel has come to a complete stop before
putting the tool down.
Hold the tool firmly with both hands. Turn the tool on
and then apply the wheel or disc to the workpiece.
In general, keep the edge of the wheel or disc at an
angle of about 15° 30° to the workpiece surface.
During the break-in period with a new wheel, do not
work the tool in the B direction or it will cut into the
workpiece. Once the edge of the wheel has been
rounded off by use, the wheel may be worked in both
A and B directions.
6
9077/9079(E) (’100. 12. 12)
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita 9077SL wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info