Bedienungsanleitung Makita 9403 (Seite 5 von 13) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

78699

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Switch action (Fig.6)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

• The tool should not be in contact with the workpiece

surface when you turn the tools on or off. Otherwise a

poor sanding finish or damage of the belt may result.

To start the tool, simply pull the trigger. Release the trig-

ger to stop. For continuous operation, pull the trigger and

then push in the lock button. To stop the tool from the

locked position, pull the trigger fully, then release it.

Sanding operation

Hold the tool firmly with both hands. Turn the tool on and

wait until it attains full speed. Then gently place the tool

on the workpiece surface. Keep the belt flush with the

workpiece at all times and move the tool back and forth.

Never force the tool. The weight of the tool applies ade-

quate pressure. Excessive pressure may cause stalling,

overheating of the motor, burning of the workpiece and

possible kickback.

Connecting to Makita vacuum cleaner or dust collector

Cleaner sanding operations can be performed by connecting the belt sander to Makita vacuum cleaner or dust collec-

tor.

When connecting to Makita vacuum cleaner (Model 406/431), an optional hose 28 mm in inner dia. or joint 25 is neces-

sary. See the figure below.

When connecting to Makita dust collector (Model 420), the optional hose or joint is not necessary. You can connect the

belt sander directly to the hose of the dust collector.

Carbon plate (Fig.7)

For greater sanding efficiency and to help the belt run

cooler, install an optional carbon plate on the steel plate

when sanding hardwood or steel.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacement of carbon brushes (Fig.8&9)

Replace carbon brushes when they are worn down to the

limit mark. Both identical carbon brushes should be

replaced at the same time.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Center.

ACCESSORIES

CAUTION:

These accessories or attachments are recommended for

use with your Makita tool specified in this manual. The

use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory or

attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Abrasive belt

Type AA: For wood, iron and steel

Type CC: For stone and plastics

• Dust bag

• Hose 28 mm in inner diameter

• Joint 25

• Carbon plate

Makita vacuum cleaner Hose for vacuum cleaner

Hose 28 mm in inner dia.

(When connecting to vacuum cleaner Model 406)

Joint 25

(When connecting to vacuum cleaner Model 431)

Grit (AA) 40 60 80 100 120 150 180 240

Use Coarse Medium Fine

Grit (CC) 40 60 80 100 120 150 180 240

Use Coarse Medium Fine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 9403 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info