Bedienungsanleitung Makita 9558HN (Seite 4 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

593090

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH (Original instructions)

Explanation of general view

1 Shaft lock

2 Switch lever

3 Wheel guard

4Screw

5 Bearing box

6Lock nut

7 Depressed center grinding

wheel/Multi-disc

8 Inner flange

9 Lock nut wrench

10 Abrasive cut-off wheel/diamond

wheel

11 Wheel guard for abrasive cut-off

wheel/diamond wheel

12 Exhaust vent

13 Inhalation vent

SPECIFICATIONS

Model 9556HN 9557HN 9558HN

Depressed center wheel diamiter...........................100 mm 115 mm 125 mm

Spindle thread .......................................................M10 M14 M14

Rated speed (n) / No load speed (n

) .................... 11,000 min

-1

11,000 min

-1

11,000 min

-1

Overall length ........................................................271 mm 271 mm 271 mm

Net weight .............................................................1.9 kg 2.0 kg 2.1 kg

Safety class ........................................................... /II /II /II

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

ENE048-1

Intended use

The tool is intended for grinding, sanding and cutting of

metal and stone materials without the use of water.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future refer-

ence.

GEB033-4

GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding,

Wire Brushing, or Abrasive Cutting-Off Operations:

1. This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations

and specifications provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.

2. Operations such as polishing are not recom-

mended to be performed with this power tool.

Operations for which the power tool was not designed

may create a hazard and cause personal injury.

3. Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can-

not be adequately guarded or controlled.

6. The arbour size of wheels, flanges, backing pads

or any other accessory must properly fit the

spindle of the power tool. Accessories with arbour

holes that do not match the mounting hardware of

the power tool will run out of balance, vibrate exces-

sively and may cause loss of control.

7. Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory is

dropped, inspect for damage or install an undam-

aged accessory. After inspecting and installing

an accessory, position yourself and bystanders

away from the plane of the rotating accessory

and run the power tool at maximum no-load

speed for one minute.

Damaged accessories will

normally break apart during this test time.

8. Wear personal protective equipment. Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear dust

mask, hearing protectors, gloves and workshop

apron capable of stopping small abrasive or

workpiece fragments. The eye protection must be

capable of stopping flying debris generated by vari-

ous operations. The dust mask or respirator must be

capable of filtrating particles generated by your oper-

ation. Prolonged exposure to high intensity noise

may cause hearing loss.

9. Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may fly away

and cause injury beyond immediate area of opera-

tion.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 9558HN Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info