Bedienungsanleitung Makita 9560C (Seite 6 von 10) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448266

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

OPERATING INSTRUCTIONS

Installing wheel guard (Fig. 1 & 2)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the wheel guard.

Pull the lever in the direction of the arrow after loosening

the screw.

Install the wheel cover on the bearing box by adjusting

the convex of the wheel cover to the concave of the bear-

ing box.

Turn the wheel cover by 180 degrees. Fasten it with the

screw after pulling lever in the direction of the arrow for

the working purpose, the setting angle of the wheel cover

can be adjusted with the lever.

Removing wheel cover

Follow the installation procedure in reverse to remove the

wheel cover.

Installing side grip (auxiliary handle) (Fig. 3)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the side grip.

Always install the side grip on the tool securely before

operation. The side grip can be installed on either side of

the tool, whichever is convenient and keeps the guard

properly positioned. Always hold the tool’s switch handle

and the side grip firmly with both hands during operation.

Shaft lock (Fig. 4)

Press the shaft lock to prevent spindle rotation when

installing or removing accessories.

CAUTION:

Never actuate the shaft lock when the spindle is moving.

The tool may be damaged.

Installing or removing depressed center wheel

(Fig. 5 & 6)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the wheel.

Mount the inner flange onto the spindle. Fit the wheel on

over the inner flange and screw the lock nut onto the

spindle.

To tighten the lock nut, press the shaft lock firmly so that

the spindle cannot revolve, then use the lock nut wrench

and securely tighten clockwise. To remove the wheel, fol-

low the installation procedure in reverse.

Switch action (Fig. 7)

CAUTION:

Before plugging in the tool, always check to see that the

switch actuates properly and returns to the “OFF” posi-

tion when the side of the switch lever is depressed.

To start the tool, slide the switch lever to “I” position.

For continuous operation, depress the front of the switch

lever and then slide to “I” position as above. The switch is

locked on the position for continuous operation. To stop

the tool from the locked position, slide the switch lever to

“O” position with depressing the rear of the switch lever.

Speed adjusting dial (For model 9560CV, 9561CV,

9562CV, 9563CV, 9564CV, 9565CV) (Fig. 8)

The rotating speed can be changed by turning the speed

adjusting dial to a given number setting from 1 to 5.

Higher speed is obtained when the dial is turned in the

direction of number 5. And lower speed is obtained when

it is turned in the direction of number 1. Refer to the table

below for the relationship between the number settings

on the dial and the approximate rotating speed.

CAUTION:

• If the tool is operated continuously at low speeds for a

long time, the motor will get overloaded and heated up.

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

The tools equipped with electronic function are easy to

operate because of the following features.

• Constant speed control

Electronic speed control for obtaining constant speed.

Possible to get fine finish, because the rotating speed

is kept constantly even under the loaded condition.

• Soft start feature

Safety and soft start because of suppressed starting

shock.

• Overload protector

When the tool would be employed over the admissible

load, it will stop automatically to protect the motor and

wheel. When the load will come to the admissible level

again, the tool can be started automatically.

Operation (Fig. 9)

CAUTION:

After operation, always switch off the tool and wait until

the wheel has come to a complete stop before putting the

tool down.

Hold the tool firmly with both hands. Turn the tool on and

then apply the wheel or disc to the workpiece.

In general, keep the edge of the wheel or disc at an angle

of about 15° – 30° to the workpiece surface. During the

break-in period with a new wheel, do not work the tool in

the B direction or it will cut into the workpiece. Once the

edge of the wheel has been rounded off by use, the

wheel may be worked in both A and B directions.

WARNING:

• It should never be necessary to force the tool. The

weight of the tool applies adequate pressure. Forcing

and excessive pressure could cause dangerous wheel

breakage.

• Continued use of a worn-out wheel may result in wheel

explosion and serious personal injury.

Number min

–1

(R.P.M.)

12,800

24,000

36,500

49,000

5 11,000

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 9560C Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info