Bedienungsanleitung Makita 9562CR (Seite 8 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Norwegisch)

448277

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Shaft lock (Fig. 1)

CAUTION:

• Never actuate the shaft lock when the spindle is

moving. The tool may be damaged.

Press the shaft lock to prevent spindle rotation when

installing or removing accessories.

Switch action (Fig. 2)

CAUTION:

• Before plugging in the tool, always check to see that

the slide switch actuates properly and returns to the

“OFF” position when the rear of the slide switch is

depressed.

To start the tool, slide the slide switch toward the “I (ON)”

position. For continuous operation, press the front of the

slide switch to lock it.

To stop the tool, press the rear of the slide switch, then

slide it toward the “O (OFF)” position.

Indication lamp

For Models 9561CVR, 9562CVR, 9564CVR, 9565CVR

(Fig. 3)

For Models 9561CR, 9562CR, 9564CR, 9565CR (Fig. 4)

The indication lamp lights up green when the tool is

plugged. If the indication lamp does not light up, the mains

cord or the controller may be defective. The indication

lamp is lit but the tool does not start even if the tool is

switched on, the carbon brushes may be worn out, or the

controller, the motor or the ON/OFF switch may be

defective.

Unintentional restart proof

The tool does not start with the switch being lock-on even

when the tool is plugged.

At this time, the indication lamp flickers red and shows the

unintentional restart proof device is on function.

To cancel the unintentional restart proof, return the slide

switch to “O (OFF)” position, then release it.

Speed adjusting dial

For 9561CVR, 9562CVR, 9564CVR, 9565CVR (Fig. 5)

The rotating speed can be changed by turning the speed

adjusting dial to a given number setting from 1 to 5.

Higher speed is obtained when the dial is turned in the

direction of number 5. And lower speed is obtained when

it is turned in the direction of number 1.

Refer to the below table for the relationship between the

number settings on the dial and the approximate rotating

speed.

CAUTION:

• If the tool is operated continuously at low speeds for a

long time, the motor will get overloaded and heated up.

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

The tools equipped with electronic function are easy to

operate because of the following features.

• Electronic constant speed control

Possible to get fine finish, because the rotating speed

is kept constantly even under the loaded condition.

• Soft start feature

Soft start because of suppressed starting shock.

• Overload protector

When the load on the tool exceeds admissible levels,

power to the motor is reduced to protect the motor from

overheating. When the load returns to admissible

levels, the tool will operate as normal.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing side grip (handle) (Fig. 6)

CAUTION:

• Always be sure that the side grip is installed securely

before operation.

Screw the side grip securely on the position of the tool as

shown in the figure.

Installing or removing wheel guard

For tool with locking screw type wheel guard (Fig. 7)

CAUTION:

• The wheel guard must be fitted on the tool so that the

closed side of the guard always points toward the

operator.

Mount the wheel guard with the protrusion on the wheel

guard band aligned with the notch on the bearing box.

Then rotate the wheel guard around 180 degrees

counterclockwise. Be sure to tighten the screw securely.

To remove wheel guard, follow the installation procedure

in reverse.

For tool with clamp lever type wheel guard (Fig. 8 & 9)

Pull the lever in the direction of the arrow after loosening

the screw. Mount the wheel guard with the protrusion on

Number min

-1

(R.P.M.)

1 2,800

2 4,000

3 6,500

4 9,000

511,000

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 9562CR Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info