Bedienungsanleitung Makita AC3610 (Seite 6 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598389

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Battery/motor protection system

The battery cartridge and tool are provided with protection

devices that will automatically reduce or cut off power to

the tool when overload situations develop that may cause

damage to the tool or battery cartridge.

If the tool becomes overloaded but not locked up a

protector is provided to reduce the revolutions to protect

the motor. In this case the two indicator lamps described

in the table below do not light or blink.

All other protection functions can be identified by the

indicator lamps described in the table below. (Fig. 6)

010823

Battery remaining capacity indicator (only

for models with Battery AP-3622)

Battery AP-3622 is equipped with the battery remaining

capacity indicator. (Fig. 7)

Press the CHECK button to indicate the battery remaining

capacity. The indicator lamps will then light for approx.

three seconds.

011713

• When only the lowermost indicator lamp (next to the

“E”) blinks, or when none of the indicator lamps light,

the battery capacity has run out, so the tool does not

operate. In these cases, charge the battery or replace

the empty battery with a fully charged one.

• When two or more indicator lamps do not light even

after charging is complete, the battery has reached the

end of its service life.

• When the upper two and lower two indicator lamps light

alternately, the battery may have malfunctioned.

Contact your local Dolmar authorized service center.

NOTE:

• The indicated capacity may be lower than the actual

level during use or immediately after using the tool.

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

ASSEMBLY

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before carrying out

any work on the tool. Failure to switch off and remove

the battery cartridge may result in serious personal

injury from accidental start-up.

• Never start the tool unless it is completely

assembled. Operation of the tool in a partially

assembled state may result in serious personal injury

from accidental start-up.

Installing the grip (Fig. 8)

Securely fit the barrier and grip onto the shaft pipe with

two screws and clamps.

Make sure that the spacer on the shaft pipe is located

between the grip and the hanger. Do not remove or shrink

the spacer.

CAUTION:

• Never install the grip on the label or joint.

NOTE:

• In some countries, the barrier and spacer are not

provided with the tool. In that case, align the handle to

Status Action to be taken

– Blinking

Battery power has been nearly

used up.

Replace the battery with fully charged one.

– Lighting On

Battery protector is shutting off

the power - battery power has

been used up.

Replace the battery with fully charged one.

Blinking –

Overload protector is shutting off

the power - the motor was locked.

Release the switch trigger and remove the

cause of the motor lock or overload. If the

cutting tool is locked by entangling weeds or the

like, always remove the battery cartridge before

clearing it.

Lighting On –

Overheat protector is shutting

off the power - overheating.

Rest the equipment for a while.

Blinking Blinking

Electric or electronic malfunction Ask your local authorized service center for

repairs.

Indicator lamps

Remaining capacity

Lighted Off Blinking

E F

70% to 100%

45% to 70%

20% to 45%

0% to 20%

Charge the battery.

The battery may

have malfunctioned.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita AC3610 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info