691772
7
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
7
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
Note: Specifications may differ from country to country.
Symbols
END106-2
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
............. Read instruction manual.
............. Wear safety glasses.
............. Do not use on scaffoldings, ladders.
IMPORTANT SAFETY
INSTRUCTIONS ENB110-1
WARNING: WHEN USING THIS TOOL, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED
TO REDUCE THE RISK OF PERSONAL INJURY,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
For personal safety and proper operation and
maintenance of the tool, read this instruction manual
before using the tool.
Always wear safety glasses to protect your eyes from
dust or nail injury.
WARNING:
It is an employer’s responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
For Australia and New Zealand only Always wear
safety glasses and face shield to protect your eyes
from dust or nail injury. The safety glasses and the face
shield should conform with the requirements of
AS/NZS 1336.
WARNING:
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
(Fig. 1)
Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or
rolled up. No necktie should be worn.
Rushing the job or forcing the tool is dangerous.
Handle the tool carefully. Do not operate when under
the influence of alcohol, drugs or the like.
General Tool Handling Guidelines:
(1) Always assume that the tool contains fasteners.
(2) Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
(3) Do not activate the tool unless the tool is placed
firmly against the workpiece.
(4) Respect the tool as a working implement.
(5) No horseplay.
(6) Do not hold or carry the tool with a finger on the
trigger.
1. Safety glasses
2. Face shield
3. Compressor air output per minute
4. Nailing frequency (times/min.)
5. Locking position
6. Released position
7. Lock lever
8. Trigger
9. Contact element
10. Adjuster
11. Too deep
12. Flush
13. Too shallow
14. Lever
15. Sliding door
16. Magazine
17. Nail
18. Groove for the sliding door
19. Grooves at the bottom of the
magazine
20. Nail discharge opening
21. Front driver guide
22. Nose adapter
23. Protrusion
24. Holder
25. Nose adapter
26. Place first the contact element
against workpiece.
27. Holder
28. Hex wrench
29. Rear driver guide
30. Screws
31. Humid
32. Hot
33. Cap
34. Drain cock
35. Air filter
36. Oiler
37. Pneumatic oil
38. Thinner
39. Stove
Model AF550H
Air pressure 0.98 - 2.26 MPa (9.8 - 22.6 bar)
Nail length 15 mm - 55 mm
Nail capacity 100 pcs.
Dimensions (L X H X W) 228 mm X 61 mm X 235 mm
Min. hose diameter 5.0 mm or more
Net weight 1.2 Kg
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita AF550H wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info