Bedienungsanleitung Makita AN510H (Seite 8 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598397

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Connecting air hose

Slip the air socket of the air hose onto the air fitting on the

nailer. Be sure that the air socket locks firmly into position

when installed onto the air fitting. A hose coupling must

be installed on or near the tool in such a way that the

pressure reservoir will discharge at the time the air sup-

ply coupling is disconnected.

OPERATION

CAUTION:

• Make sure all safety systems are in working order

before operation.

1. To drive a nail, you may place the contact element

against the workpiece and pull the trigger,

2. Pull the trigger first and then place the contact ele-

ment against the workpiece. (Fig. 13 & 14)

• No. (1) method is for intermittent nailing, when you wish

to drive a nail carefully and very accurately. No. (2)

method is for continuous nailing.

CAUTION:

• However when the tool is set to the “Intermittent Nail-

ing” mode, WITH THE TRIGGER HELD IN A HALF-

PULLED POSITION, an unexpected nailing could

occur, if contact element is allowed to re-contact

against the workpiece or the other surface under the

influence of recoil.

In order to avoid this unexpected nailing, perform as fol-

lows;

A. Do not place the contact element against the work-

piece with excessive force.

B. Pull the trigger fully and hold it on for 1 – 2 seconds

after nailing.

• For No. (1) method, set the change lever to the

position.

For No. (2) method, set the change lever to the

position.

After using the change lever to change the nailing

method, always make sure that the change lever is

properly set to the position for the desired nailing

method. (Fig. 15 & 16)

Cutting off the sheet (Fig. 17)

CAUTION:

• Always disconnect the hose before cutting off the

sheet.

Tear off the output sheet in the direction of the arrow

when using the sheet collated nails.

MAINTENANCE

CAUTION:

• Always disconnect the air hose from the tool before

attempting to perform inspection or maintenance.

Jammed nailer (Fig. 18 & 19)

CAUTION:

• Always disconnect the air hose and remove the nails

from the magazine before cleaning a jam.

When the nailer becomes jammed, do as follows:

Open the magazine cap and remove the nail coil. Insert a

small rod or the like into the ejection port and tap it with a

hammer to drive out the nail jamming from the ejection

port. Reset the nail coil and close the magazine cap.

Drain tool

Remove the hose from the tool. Place the tool so that the

air fitting faces down to the floor. Drain as much as possi-

ble.

Cleaning of tool

Iron dust that adhere to the magnet can be blown off by

using an air duster.

Cap (Fig. 20)

When not in use, disconnect the hose. Then cap the air

fitting with the cap.

Storage

When not in use, the nailer should be stored in a warm

and dry place.

Maintenance of compressor, air set and air hose

After operation, always drain the compressor tank and

the air filter. If moisture is allowed to enter the tool, it may

result in poor performance and possible tool failure.

(Fig. 21 & 22)

Check regularly to see if there is sufficient pneumatic oil

in the oiler of the air set. Failure to maintain sufficient

lubrication will cause O-rings to wear quickly. (Fig. 23)

Keep the air hose away from heat (over 60°C, over

140°F), away from chemicals (thinner, strong acids or

alkalis). Also, route the hose away from obstacles which

it may become dangerously caught on during operation.

Hoses must also be directed away from sharp edges and

areas which may lead to damage or abrasion to the hose.

(Fig. 24)

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Nails

• Air hoses

• Safety goggles

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita AN510H Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info