Bedienungsanleitung Makita AN621 (Seite 6 von 60) (Deutsch, Englisch, Polnisch)

601101

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

• On rooftops and other high locations, nail as you

move forward. It is easy to lose your footing if you

nail while inching backward. When nailing against

perpendicular surface, nail from the top to the

bottom. You can perform nailing operations with

less fatigue by doing so.

• A nail will be bent or the tool can become jammed

if you mistakenly nail on top of another nail or strike

a knot in the wood. The nail may be thrown and hit

someone, or the tool itself can react dangerously.

Place the nails with care.

• Do not leave the loaded tool or the air compressor

under pressure for a long time out in the sun. Be

sure that dust, sand, chips and foreign matter will

not enter the tool in the place where you leave it

setting.

• Do not point the ejection port at anyone in the

vicinity. Keep hands and feet away from the

ejection port area.

• When the air hose is connected, do not carry the

tool with your finger on the trigger or hand it to

someone in this condition. Accidental firing can be

extremely dangerous.

• Handle the tool carefully, as there is high pressure

inside the tool that can be dangerous if a crack is

caused by rough handling (dropping or striking).

Do not attempt to carve or engrave on the tool.

• Stop nailing operations immediately if you notice

something wrong or out of the ordinary with the

tool.

• Always disconnect the air hose and remove all of

the nails:

1.When unattended.

2.Before performing any maintenance or repair.

3.Before cleaning a jam.

4.Before moving the tool to a new location.

• Perform cleaning and maintenance right after

finishing the job. Keep the tool in tip-top condition.

Lubricate moving parts to prevent rusting and

minimize friction-related wear. Wipe off all dust

from the parts.

• When not operating the tool, always lock the

trigger by turning the change lever to the LOCK

position.

• Do not modify tool without authorization from

Makita.

• Ask Makita's Authorized service centers for

periodical inspection of the tool.

• To maintain product SAFETY and RELIABILITY,

maintenance and repairs should be performed by

Makita Authorized Service Centers, always using

Makita replacement parts.

• Use only pneumatic tool oil specified in this

manual.

• Never connect tool to compressed air line where

the maximum allowable pressure of tool cannot be

exceeded by 10 %. Make sure that the pressure

supplied by the compressed air system does not

exceed the maximum allowable pressure of the

fastener driving tool. Set the air pressure initially to

the lower value of the recommended allowable

pressure.

• Do not attempt to keep the trigger contact element

depressed with tape or wire. Death or serious

injury may occur.

• Always check contact element as instructed in this

manual. Nails may be driven accidentally if the

safety mechanism is not working correctly.

SAVE THESE INSTRUCTIONS.

INSTALLATION

Selecting compressor

100

120

10 20 30 40 50 60

Compressor air output per minute

(L/min)

Nailing frequency

(times/min)

0.83Mpa(8.3bar)

0.69Mpa(6.9bar)

0.59Mpa(5.9bar)

0.44Mpa(4.4bar)

005236

The air compressor must comply with the requirements

of EN60335-2-34.

Select a compressor that has ample pressure and air

output to assure cost-efficient operation. The graph

shows the relation between nailing frequency, applicable

pressure and compressor air output.

Thus, for example, if nailing takes place at a rate of

approximately 50 times per minute at a compression of

0.59 MPa (5.9 bar), a compressor with an air output over

80 liters/minute is required.

Pressure regulators must be used to limit air pressure to

the rated pressure of the tool where air supply pressure

exceeds the tool's rated pressure. Failure to do so may

result in serious injury to tool operator or persons in the

vicinity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita AN621 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info