Bedienungsanleitung Makita AN901 (Seite 8 von 60) (Deutsch, Englisch, Polnisch)

601100

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Loading nailer

Select nails suitable for your work. Depress the latch

lever and open the door and magazine cap.

Fig.7

Lift and turn the coil support plate to set it to the correct

step. When loading 90 mm long nails, use the bottom

step. When loading 65 or 75 mm long nails, use the

middle step. When loading 45 or 50 or 57 mm long nails,

use the top step. If the tool is operated with the coil

support plate set to the wrong step, poor nail feed or

malfunction of the tool may result.

Fig.8

Place the nail coil over the coil support plate. Uncoil

enough nails to reach the feed claw. Place the first nail in

the driver channel and the second nail in the feed claw.

The nail heads must be in the slot in the feeder body.

Place other uncoiled nails on feeder body. Close the

magazine cap and door after checking to see that the nail

coil is set properly in the magazine.

Fig.9

Connecting air hose

Lock the trigger. Slip the air socket of the air hose onto

the air fitting on the nailer. Be sure that the air socket

locks firmly into position when installed onto the air fitting.

A hose coupling must be installed on or near the tool in

such a way that the pressure reservoir will discharge at

the time the air supply coupling is disconnected.

Fig.10

OPERATION

CAUTION:

• Make sure all safety systems are in working order

before operation.

Fig.11

Fig.12

1. To drive a nail, you may place the contact element

against the workpiece and pull the trigger, or

2. Pull the trigger first and then place the contact

element against the workpiece.

No. 1 method is for intermittent nailing, when you wish to

drive a nail carefully and very accurately.

No. 2 method is for continuous nailing.

CAUTION:

• However when the tool is set to the "Intermittent

Nailing" mode, WITH THE TRIGGER HELD IN A

HALF-PULLED POSITION, an unexpected nailing

could occur, if contact element is allowed to

re-contact against the workpiece or the other

surface under the influence of recoil.

In order to avoid this unexpected nailing, perform

as follows;

A. Do not place the contact element against the

workpiece with excessive force.

B. Pull the trigger fully and hold it on for 1-2 seconds

after nailing.

For No. 1 method, set the change lever to the

"Intermittent Nailing" position. For No. 2 method, set the

change lever to the "Continuous Nailing" position. After

using the change lever to change the nailing method,

always make sure that the change lever is properly set to

the position for the desired nailing method.

Fig.13

CAUTION:

• Operating the tool without nails shortens the life of

the tool and should be avoided.

Air exhaust

Air exhaust direction can be changed easily by rotaiting

the exhaust cover. Change it when necessary.

Jammed nailer

Fig.14

CAUTION:

• Always lock the trigger, disconnect the hose and

remove the nails from the magazine before

cleaning a jam.

When the nailer becomes jammed, do as follows:

Open the door and magazine cap and remove the nail

coil. Insert a small rod or the like into the ejection port and

tap it with a hammer to drive out the nail jamming from

the ejection port. Reset the nail coil and close the

magazine cap and door.

Hook

Fig.15

Fig.16

The hook is convenient for hanging the tool temporarily.

This hook can be installed on either side of the tool.

CAUTION:

• Always lock the trigger and disconnect the hose

when hanging the tool using the hook.

• Always tighten the hook securing bolt firmly. Loose

bolt may cause air leakage from the tool.

• Never hang the tool on a waist belt or like.

Dangerous accidental firing may result.

Nails

Nail

004310

Handle nail coils and their box carefully. If the nail coils

have been handled roughly, they may be out of shape or

their connector breaks, causing poor nail feed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita AN901 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info