Bedienungsanleitung Makita AN935H (Seite 8 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657979

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

8 ENGLISH

Save all warnings and instruc-

tions for future reference.

Forpersonalsafetyandproperoperationandmainte-

nanceofthetool,readthisinstructionmanualbefore

using the tool.

General safety

1. Do not permit those uninstructed to use the

tool.

2. No horseplay. Respect the tool as a working

implement.

3. Do not operate when under the inuence of

alcohol, drugs or the like.

4. Never alter the tool.

Personal protective equipments

►Fig.1

1. Always wear safety glasses to protect your

eyes from dust or fastener injury.

WARNING: It is an employer's responsibility

to enforce the use of safety eye protection

equipment by the tool operators and by other

persons in the immediate working area.

For Australia and New Zealand only

Always wear safety glasses and face shield to

protect your eyes from dust or fastener injury.

Thesafetyglassesandthefaceshieldshould

conformwiththerequirementsofAS/NZS1336.

2. Wear hearing protection to protect your ears

against exhaust noise and head protection.

Also wear light but not loose clothing. Sleeves

should be buttoned or rolled up. No necktie

should be worn.

Work area safety

1. Keep work area clean and well lit.Clutteredor

dark areas invite accidents.

2. Do not operate the tool in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Operating the tool can

createsparkswhichmayignitethedustorfumes.

3. Keep children and bystanders away while

operating the tool. Distractions can cause you to

lose control.

4. Illuminate the work area sufciently.

5. There may be local regulations concerning

noise which must be complied with by keeping

noise levels within prescribed limits. In certain

cases, shutters should be used to contain

noise.

Safety devices

1. Make sure all safety systems are in working

order before operation. Thetoolmustnotoper-

ateifonlythetriggerispulledorifonlythecontact

arm is pressed against the wood. It must work only

whenbothactionsareperformed.Testforpossible

faultyoperationwithfastenersunloadedandthe

pusherinfullypulledposition.

2. Do not play with the contact element: it pre-

vents accidental discharge, so it must be kept

on and not removed. Securing the trigger in the

ON position is also very dangerous. Never attempt

tofastenthetrigger.Donotoperateatoolifany

portionofthetooloperatingcontrolsisinoperable,

disconnected,altered,ornotworkingproperly.

3. Do not attempt to keep the contact element

depressed with tape or wire. Death or serious

injurymayoccur.

4. Always check contact element as instructed

in this manual. Fasteners may be driven acci-

dentallyifthesafetymechanismisnotworking

correctly.

Loading fasteners

1. Do not load the tool with fasteners when any

one of the operating controls is activated.

2. Use only fasteners specied in this manual.

Theuseofanyotherfastenersmaycausemal-

functionofthetool.

Power source

1. Never connect the tool to compressed air line

where the air pressure can exceed the suitable

air pressure range of the tool, specied in the

"SPECIFICATIONS" table, by 10%. Make sure

that the pressure supplied by the compressed air

system does not exceed the suitable air pressure

rangeofthetool.Settheairpressureinitiallyto

thelowervalueofthesuitableairpressurerange.

2. When using the tool operated by compressed

air, particular attention must be paid to avoid

exceeding the maximum allowable pressure.

3. Operate the tool at the lowest pressure

required for the application, in order to prevent

unnecessarily high noise levels, increased

wear and resulting failures.

4. Never use the tool with other than compressed

air.Ifbottledgas(carbondioxide,oxygen,

nitrogen,hydrogen,air,etc.)orcombustiblegas

(hydrogen,propane,acetylene,etc.)isusedasa

powersourceforthistool,thetoolwillexplodeand

causeseriousinjury.

5. Always disconnect the air hose and remove all

of the fasteners:

— when unattended;

— beforeperforminganymaintenanceor

repair;

— beforecleaningajam;

— beforemovingthetooltoanewlocation.

6. Use only pneumatic tool oil specied in this

manual.

Operational safety

1. Always check the tool for its overall condition

and loose screws before operation. Tighten as

required.

2. Handle the tool carefully, as there is high pres-

sure inside the tool that can be dangerous if a

crack is caused by rough handling (dropping

or striking). Do not attempt to carve or engrave

on the tool.

3. Stop the operation immediately if you notice

something wrong or out of the ordinary with

the tool.Animproperlyfunctioningtoolmustnot

be used.

4. Do not point the ejection port at anyone in the

vicinity. Keep hands and feet away from the

ejection port area.

5. Always assume that the tool contains

fasteners.

Makita AN935H Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info