Bedienungsanleitung Makita AN935H (Seite 11 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657979

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

11 ENGLISH

3. Turntheadjustshaftandsetthestepofthe

changeplatesuitableforthenaillength.Makesurethat

the arrow points to the corresponding graduation incre-

mentofthenaillengthmarkedontheadjustshaft.

►Fig.14: 1.Changeplate2.Adjustshaft3. Arrow

NOTICE:Ifthetoolisoperatedwiththechange

platesettothewrongstep,itmayresultinpoornail

feedingortoolmalfunction.

4. Place the nail coil over the change plate and

uncoil enough nails to reach the nail rail.

Thenplacetherstnailinthenailrailandthesecond

nailinthefeedclaw.Also,placeotheruncoilednailson

feederbody.

►Fig.15: 1. Nail rail 2. Feed claw

5. Checkthatthenailcoilissetproperlyinthe

magazine.

6. Closethemagazinecapcarefully.Thenwith

depressingthelatchlever,closethedooruntilthelatch

lever locks.

Connecting air hose

CAUTION: Do not connect the air hose with

a nger on the trigger. An unexpected driving will

causeseriousinjury.

►Fig.16: 1.Airtting2. Air socket

Sliptheairsocketoftheairhoseontotheairttingon

thenailer.Besurethattheairsocketlocksrmlyinto

positionwheninstalledontotheairtting.

A hose coupling must be installed on or near the tool in

such a way that the pressure reservoir will discharge at

the time the air supply coupling is disconnected.

Changing the trigger for contact

actuation mode

CAUTION: Always disconnect the air hose

and unload the tool with nails before replacing

the trigger.

CAUTION: After the trigger replacement,

always check that the tool operates properly

before actual work. Do not load the tool with any

nails before checking the function to avoid unex-

pected nailing.

Thetriggerforsinglesequentialactuationmodeis

factory-installed.Tochangethenailingmodetocontact

actuation,replacethetriggerpartwiththeoneforcon-

tact actuation.

►Fig.17: 1.Triggerforcontactactuation2. Silver part

3.Triggerforsinglesequentialactuation

4. Black part

1. Turnthetriggerlocklevertothelockposition

►Fig.18: 1.Triggerlocklever

2. Pushthepinsecuringthetriggerfromtheure-

thanewasherside,andthenremovetheurethane

washer.Thenpulloutthepinandremovethetrigger.

►Fig.19: 1. Pin 2. Urethane washer 3.Trigger

3. Setthetriggerassemblyforcontactactuation.

Withpushinginthehingedpartinward,setthetrigger

sothatthehingedpartisundertherodofthevalvein

the housing.

►Fig.20: 1. Hinged part 2.Rodofthevalve

4. Insert the pin to the hole and secure it by urethane

washer.

5. Connecttheairhose,andmakesurethatthe

tooloperatesproperly.Refertothesection“Checking

properactionbeforeoperation”.

NOTE:Tosetbacktosinglesequentialactuation,

followtheproceduresforchangingthetriggerabove.

OPERATION

CAUTION: Make sure all safety systems are in

working order before operation.

CAUTION: When operating the tool, do not

close the face to the tool. Also keep hands and

feet away from the ejection port area.

CAUTION: When not operating the tool,

always lock the trigger by turning the trigger lock

lever to the lock position .

CAUTION: Make sure that the trigger is

locked when the trigger lock lever is set to the

lock position .

Checking proper action before

operation

Beforeoperation,alwayscheckfollowingpoints.

— Make sure that the tool does not operate only by

connecting the air hose.

— Make sure that the tool does not operate only by

pulling the trigger.

— Make sure that the tool does not operate only by

placing the contact element against the workpiece

without pulling the trigger.

►Fig.21: 1.Contactelement2. Workpiece 3.Trigger

(not pulled)

— Insinglesequentialactuationmode,makesure

that the tool does not operate when pulling the

triggerrstandthenplacingthecontactelement

against the workpiece.

►Fig.22

Nailing method

Topreventthetriggerfrombeingaccidentallypulled,

the trigger lock lever is provided.

Tolockthetrigger,turnthetriggerlocklevertothelock

position

Tousethetool,turnthetriggerlocklevertotheunlock

position .

►Fig.23: 1.Triggerlocklever2.Trigger

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita AN935H Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info