601094
7
Zoom out
Zoom in
Vorherige Seite
1/68
Nächste Seite
7
ENGLISH
Explanation of general view
1 Compressor air output per
minute
2 Stapling frequency (times/min)
3 Depth adjusting plate
4Hex wrench
5Hook
6Screw
7 Lock pin
8 Pusher
9 Air fitting
10 Air socket
11 Trigger
12 Contact element
13 Workpiece
14 Exhaust cover
15 Driver guide
16 Latch
17 Slotted bit screwdriver
18 Latch
19 Door
20 Drain cock
21 Air filter
22 Oiler
23 Pneumatic oil
SPECIFICATIONS
Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
Note: Specifications may differ from country to country.
IMPORTANT SAFETY INSTRUCTIONS
ENB103-1
WARNING: WHEN USING THIS TOOL, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE FOL-
LOWED TO REDUCE THE RISK OF PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
For personal safety and proper operation and main-
tenance of the tool, read this instruction manual
before using the tool.
• Always wear safety glasses to protect your eyes
from dust or staple injury.
WARNING:
It is an employer’s responsibility to enforce the use
of safety eye protection equipment by the tool
operators and by other persons in the immediate
working area.
For Australia and New Zealand only
Always wear safety glasses and face shield to pro-
tect your eyes from dust or staple injury. The safety
glasses and the face shield should conform with
the requirements of AS/NZS 1336.
WARNING:
It is an employer’s responsibility to enforce the use
of safety eye protection equipment by the tool
operators and by other persons in the immediate
working area.
Wear hearing protection to protect your ears
against exhaust noise and head protection. Also
wear light but not loose clothing. Sleeves should
be buttoned or rolled up. No necktie should be
worn.
• Rushing the job or forcing the tool is dangerous.
Handle the tool carefully. Do not operate when
under the influence of alcohol, drugs or the like.
General Tool Handling Guidelines:
1. Always assume that the tool contains fasteners.
2. Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
3. Do not activate the tool unless the tool is placed
firmly against the workpiece.
4. Respect the tool as a working implement.
5. No horseplay.
6. Do not hold or carry the tool with a finger on the
trigger.
7. Do not load the tool with fasteners when any one
of the operating controls is activated.
8. Do not operate the tool with any power source
other than that specified in the tool operating/
safety instructions.
An improperly functioning tool must not be used.
Model AT1150A AT2550A
Air pressure 0.44 – 0.83 MPa (4.4 – 8.3 bar)
Applicable staples 25 mm – 50 mm
Staple capacity 140 pcs.
Min. hose diameter 6.5 mm
Dimensions (L x W x H) 370 mm x 87 mm x 290 mm 370 mm x 76 mm x 260 mm
Net weight 2.3 kg 2.3 kg
Safety glasses
Face shield
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita AT1150A wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info