Bedienungsanleitung Makita B7660WH (Seite 13 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690564

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

3. Loosen the oil drain bolt to let the oil drain out. Be careful not to

allow oil to get on the fuel tank or other parts.

NOTICE: Be careful not to lose the gasket (aluminum washer).

Put the oil drain bolt in a location where it does not get dirt.

4. Remove the oil cap. (Removing the oil cap allows the oil to drain

easily.)

NOTICE: Be sure to set the oil cap down in a location where it

does not get dirt.

5. As the level of the oil being drained decreases, tilt the blower

over on to the side with the drain so that the oil will completely drain

out.

6. After the oil has completely drained out, tighten the oil drain bolt

securely. If the bolt is not tightly fastened, it may result in oil leakage.

NOTICE: Do not forget to put the gasket (aluminum washer)

back on when reattaching the drain plug.

7. Pour approximately 220 ml oil into the oil rell port up to the

upper limit of the oil gauge.

► 1. Oil gauge 2. Upper limit mark 3. 100 ml level 4. Lower limit

mark

8. After lling with oil, tighten the oil cap securely to prevent oil

leaks.

NOTICE: Do not forget to put the oil cap gasket back on when

reattaching the oil cap.

Cleaning of air cleaner

WARNING: INFLAMMABLES STRICTLY PROHIBITED

Interval of Cleaning and Inspection

Daily (every 10 operating hours)

Cleaning procedure

► 1. Knob bolts 2. Air cleaner cover 3. Element 4. Breather

1. Loosen the knob bolts.

2. Remove the air cleaner cover.

3. Remove the element and clean off any dirt from the element with

a cloth or air blow. Replace the element with a new one if it is dam-

aged or very dirty.

NOTE: The element is a dry type and should not get wet. Never

wash with water.

4. Wipe off any oil around the breather with a rag or cloth.

5. Install the element in the air cleaner case.

6. Attach the air cleaner cover and tighten the knob bolts.

NOTICE: Clean the element several times a day, if excessive

dust adheres to it due to dusty environment.

NOTICE: If operation continues with the element remaining

not cleared of oil, oil in the air cleaner may fall outside, result-

ing in oil contamination.

Checking the spark plug

CAUTION: Do not touch the spark plug while the engine is

running. Otherwise electrical shock may result.

CAUTION: Set the stop control lever/stop switch to OFF

“O” position.

CAUTION: Check the spark plug cord regularly. If it is dam-

aged or torn, replace it. Otherwise electrical shock may result.

NOTICE: When removing the spark plug, clean the spark plug

and cylinder head rst, so that no dirt, sand, etc will enter the

cylinder.

NOTICE: Remove the spark plug after the engine has cooled

down in order to avoid damaging the threaded hole in the

cylinder.

NOTICE: Install the spark plug properly into the threaded

hole. If installed at an angle, the threaded hole in the cylinder will

get damaged.

1. To open the plug cover, lift it and make a half turn of it.

► 1. Plug cover

2. Use the box wrench provided as an standard accessory to

remove and install the spark plug.

13 ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita B7660WH Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info