Bedienungsanleitung Makita BBX7600 (Seite 17 von 128) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598423

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

4. Cleaning the fuel filter

• Clogged fuel filter may cause difficulty of start-up or failure of engine speed

increase.

• Check the fuel filter regularly as follows:

(1) Remove the fuel tank cap, drain the fuel to empty the tank. Check the

tank inside for any foreign materials. If any, wipe clean such materials.

(2) Pull out the fuel filter with wire through the oil filling port.

(3) If the fuel filter surface is contaminated, clean it with gasoline. Foul

gasoline must be disposed of according to the method specified by

each local authority. Excessively foul filter must be replaced.

(4) Reset the fuel filter in the fuel tank and tighten firmly the fuel tank cap.

For replacement, contact your dealership or an authorized service

agent.

5. Inspection of bolts, nuts and screws

• Retighten loose bolts, nuts, etc.

• Check for fuel and oil leakage.

• Replace damaged parts with new ones for safety operation.

6. Cleaning of parts

• Keep the engine always clean.

• Keep the cylinder fins free of dust or dirt. Dust or dirt adhering to the fins

will cause seizure.

• Blowing air is taken in from the air inlet net㧚When airflow has dropped

down during operation, stop engine and inspect the air inlet net for blocking

by obstacles.

• Note that failure to remove any such obstacles may result in the engine

becoming overheated and damaged.

WARNING :

Never use the blower without the net of the blower. Before each use,

check that the net is attached in place and is free from any damage.

7. Replacement of gaskets and packings

In reassembling after the engine is dismounted, be sure to replace the gaskets and packings with new ones.

Any maintenance of adjustment work that is not included and described in this manual is only to be performed by Authorized Service Agents.

STORAGE

㩷

Drain up fuel from the fuel tank and carburetor according to the following

procedure:

(1) Remove the fuel tank cap, and drain fuel completely.

If there is any foreign matter remaining in the fuel tank, remove it

completely.

(2) Pull out the fuel filter from the refill port using a wire.

(3) Push the primer pump until fuel is drained from there, and drain fuel

coming into the fuel tank.

(4) Reset the filter to the fuel tank, and securely tighten the fuel tank cap.

(5) Then, continue to operate the engine until it stops.

(6) Remove the spark plug, and drip several drops of engine oil through the

spark plug hole.

(7) Gently pull the starter handle so that engine oil will spread over the

engine, and attach the spark plug.

(8) During storage, please keep the machine upright.

(9) Keep the drained fuel in a special container in a well-ventilated shade.

WARNING

• When draining the fuel, be sure to stop the engine and confirm that the engine cools down.

− Just after stopping the engine, it may still hot with possibility of burns, inflammability and fire.

DANGER

• When the machine is kept out of operation for a long time, drain up all fuel from the fuel tank and carburetor, and keep it at a dry and

clean place.

Fuel tank cap

Fuel filter

Hose clamp

ir inlet net

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BBX7600 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info