Bedienungsanleitung Makita BC231UD (Seite 17 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691018

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

WARNING:

• Be extremely careful to maintain control of the tool

at all times. Do not allow the tool to be deflected

toward you or anyone in the work vicinity. Failure to

keep control of the tool could result in serious injury to

the bystander and the operator.

Adjustment of the hanger position and shoulder

harness

When replacing an accessory with another, the weight

balance of the tool may change. In such case, adjust the

hanger position and shoulder harness length as follows.

To change the hanger position, loosen the fixing screw on

the hanger with the supplied wrench and then move the

hanger.

Adjust the hanger position and shoulder harness length

so that:

- the hanger positions 750 mm or higher from the

ground,

- the cutting tool positions up to 300 mm high from the

ground and

- the unguarded part of cutting tool is horizontally

750 mm or farther away from the hanger. (Fig. 34)

After adjusting the hanger position, tighten the screw with

the wrench securely.

MAINTENANCE

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before attempting to

perform inspection or maintenance on the tool.

Failure to switch off and remove the battery cartridge

may result in serious personal injury from accidental

start-up.

NOTICE:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Supply of grease to gear case (Fig. 35)

Supply grease (Shell Alvania 2 or equivalent) to the gear

case through the grease hole every 30 hours. (Genuine

Makita grease may be purchased from your Makita

dealer.)

Replacing the nylon cord

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before attempting to

perform inspection or maintenance on the tool.

Failure to switch off and remove the battery cartridge

may result in serious personal injury from accidental

start-up.

• Make sure that the cover of the nylon cutting head

is secured to the housing properly as described

below. Failure to properly secure the cover may cause

the nylon cutting head to fly apart resulting in serious

personal injury. (Fig. 36)

Press inward on the housing latches and lift upward to

remove the cover. Discard any of the remaining nylon

cord. (Fig. 37)

Hook the middle of the new nylon cord to the notch

located at the center of the spool between the 2 channels

provided for the nylon cord. One side of the cord should

be about 80mm longer than the other side.

Wind both ends firmly around the spool in the direction

marked on the head for left hand direction indicated by

LH. (Fig. 38)

Wind all but about 100 mm of the cords, leaving the ends

temporarily hooked through a notch on the side of the

spool. (Fig. 39)

Mount the spool in the housing so that the grooves and

protrusions on the spool match up with those in the

housing. Keep the side with letters on the spool visible on

the top. Now, unhook the ends of the cord from their

temporary position and feed the cords through the eyelets

to come out of the housing. (Fig. 40)

Align the protrusion on the underside of the cover with the

slots of the eyelets. Then push cover firmly onto the

housing to secure it. Make sure the latches fully spread in

the cover.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

TROUBLE SHOOTING

Before asking for repairs, conduct your own inspection

first. If you find a problem that is not explained in the

manual, do not attempt to dismantle the tool. Instead, ask

Makita Authorized Service Centers, always using Makita

replacement parts for repairs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BC231UD Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info