Bedienungsanleitung Makita BC300LD (Seite 14 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691019

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

actuates properly and returns to the “OFF”

position when released. Do not pull the switch

trigger hard without pressing in the lock-off button.

This can cause switch breakage. Operating a tool

with a switch that does not actuate properly can lead to

loss of control and serious personal injury. (Fig. 5 & 6)

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided. To start the tool,

press in the lock-off button and pull the switch trigger. The

tool speed is increased by increasing pressure on the

switch trigger. Release the switch trigger to stop.

Reversing Switch for Debris Removal

(Fig. 7 & 8)

This tool has a reversing switch which is only provided to

change the direction of rotation so that it can be used to

remove weeds and debris entangled in the tool. To

operated the tool normally the “A” side of the switch

should be depressed.

To remove weeds and debris that are jammed in the

rotating head the tool can be reversed by depressing the

“B” side of the switch. In the reverse position the tool will

only operate for a short period of time and automatically

shut off.

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before removing

weeds or debris entangled in the tool that could not

be removed when operated in the reverse mode.

Failure to switch off and remove the battery cartridge

may result in serious personal injury from accidental

start-up.

NOTICE:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage it.

Speed change (Fig. 9 & 10)

Two speed ranges can be preselected with the speed

change switch.

Flipping the speed change switch lever to the “1” position

will set the tool to the low speed range and the “2” position

will set the tool to the high speed range.

Battery/motor protection system

The battery cartridge and tool are provided with protection

devices that will automatically reduce or cut off power to

the tool when overload situations develop that may cause

damage to the tool or battery cartridge. If the tool

becomes overloaded but not locked up a protector is

provided to reduce the revolutions to protect the motor. In

this case the two indicator lamps described in the table

below do not light or blink.

All other protection functions can be identified by the

indicator lights described in the table below. (Fig. 11)

010823

Nylon cutting head (optional accessory

for a product that comes with a cutter

blade)

NOTICE:

• Do not attempt to bump feed the head while the tool is

operating at a high RPM. Bump feeding at a high RPM

may cause damage to the nylon cutting head.

• The bump feed will not operate properly if the head is

not rotating. (Fig. 12)

The nylon cutting head is a dual string trimmer head

provided with a bump & feed mechanism. To cause the

nylon cord to feed out, the cutting head should be bumped

against the ground while rotating at a low RPM. As the

nylon cord is feeding out it will automatically be cut to the

proper length by the cutters on the guard extension.

NOTE:

If the nylon cord does not feed out while bumping the

head, rewind/replace the nylon cord by following the

procedures described under “Maintenance.”

Battery remaining capacity indicator (only

for models with Battery BL3622A)

Battery BL3622A is equipped with the battery remaining

capacity indicator. (Fig. 13)

Press the CHECK button to indicate the battery remaining

capacity. The indicator lamps will then light for approx.

three seconds.

Status Action to be taken

- Blinking Battery power has been nearly used up.

Replace the battery with fully charged

one.

- Lighting On

Battery protector is shutting off the

power - battery power has been used

up.

Replace the battery with fully charged

one.

Blinking -

Overload protector is shutting off the

power - the motor was locked.

Release the switch trigger and remove

the cause of the motor lock or overload.

If the cutting tool is locked by entangling

weeds or the like, always remove the

battery cartridge before clearing it.

Lighting On -

Overheat protector is shutting off the

power - overheating.

Rest the equipment for a while.

Blinking Blinking Electric or electronic malfunction

Ask your local authorized service center

for repairs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BC300LD Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info