Bedienungsanleitung Makita BCG180 (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598425

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

To start the tool, push the trigger-lock button from B side

and pull the switch trigger. Tool speed is increased by

increasing pressure on the switch trigger. Release the

switch trigger to stop.

After use, press in the trigger-lock button from A side.

Lighting up the lamp

CAUTION:

• Do not look in the light or see the source of light

directly. (Fig. 6)

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out approximately 10 seconds after the

switch trigger is released.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

• When the tool is overheated, the lamp flickers. Cool

down the tool fully before operating again.

Drip preventive function

The motor keeps running for a short time even after the

trigger is released. It releases the pressure of the caulking

material and prevents dripping.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

• Always place the tool on the ground or workbench

when carrying out any assembling work. The tool

without being held tight may loose balance and cause

injury.

Installing holder joint (Fig. 7)

Attach the holder joint firmly along the tool, set the plate,

and fix them with screws tightly.

To remove the holder joint, follow above procedure in

reverse.

NOTE:

• There are two types of holders (optional accessory),

short holder (300 ml) and long holder (600 ml). Use

appropriate holder joint accordingly.

Installing rod and piston (Fig. 8 & 9)

Insert the rod into the slit of the tool.

Attach the piston and tighten it with a screw.

To remove the rod and piston, follow the installation

procedure in reverse.

NOTICE:

• The teeth on the rod must point down.

• There are three types of pistons. Piston A for

cartridges. Piston B for film type packs. Piston C for

direct filling.

• Choose appropriate piston in accordance with the type

of caulking material container. Improper piston may

cause leakage or tool breakage.

• There are two types of rods. The short rod for the short

holder (300 ml), and the long rod for long holder

(600 ml). Use appropriate rod in accordance with

holder type.

• Always keep the rod and piston clean. Adhering caulk

may damage the tool.

Installing holder (Fig. 10 & 11)

Hold the bottom of the holder and the holder joint, then

turn the holder clockwise. Tighten it firmly until it stops.

Make sure the holder is tightened firmly. Otherwise the

tool may be damaged.

To remove the holder, turn it counter clockwise.

NOTE:

• You can rotate the holder in accordance with required

situations to facilitate the operation.

• The short holder (300 ml) is intended for the cartridges

only. Use only piston A with short holder (300 ml), and

do not use it with film type packs or direct filling. Also

use appropriate rod in accordance with the holder type.

Installing cartridge

NOTICE:

• Make sure the piston A is attached to the rod. Do not

use other type of piston for cartridge.

Installing the cartridge into the short holder (300 ml)

(Fig. 12)

Pull the rod handle backwards slowly until it stops.

(Fig. 13)

Insert the cartridge into the holder as illustrated.

Push the rod gently until the piston touches the bottom of

the cartridge.

To remove the cartridge, pull the rod backwards until it

stops, then lift out the cartridge.

Installing the cartridge into the long holder (600 ml)

(Fig. 14)

Remove the holder cap from the holder.

Pull the rod handle backwards slowly until it stops.

(Fig. 15)

Insert the cartridge into the holder.

Attach the holder cap. Make sure it is tightened firmly.

Push the rod gently until the piston touches the bottom of

the cartridge.

To remove the cartridge, remove the holder cap, then take

out the cartridge.

NOTICE:

• Always check the cartridge for puncture or damage

before installing. Do not use damaged cartridge,

otherwise the tool may be damaged.

• When using a partially used cartridge, remove any

adhered material on the cartridge.

Installing film type pack

NOTICE:

• Make sure the piston B is attached to the rod. Do not

use other type of piston for film type pack.

• Film type pack can be installed in the long holder

(600 ml) only.

Remove the holder cap, the nozzle and the rubber ring

from the holder.

Pull the rod handle backwards slowly until it stops.

(Fig. 16)

Cut off the tip of the film type pack.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BCG180 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info