Bedienungsanleitung Makita bdf 460 (Seite 7 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

386317

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Switch action (Fig. 7)

CAUTION:

Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the ‘‘OFF’’ position when

released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger.

Release the trigger to stop.

Reversing switch action (Fig. 8)

CAUTION:

•

Always check the direction of rotation before opera-

tion.

•

Use the reversing switch only after the tool comes to

a complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

•

When not operating the tool, always set the revers-

ing switch lever to the neutral position.

This tool has a reversing switch to change the direc-

tion of rotation. Depress the reversing switch lever

from the A side for forward rotation or from the B side

for reverse rotation. When the switch lever is in

between (the neutral position), the switch trigger

cannot be pulled.

Speed change (Fig. 9)

To change the speed, first switch off the tool and then

slide the speed change lever to the ‘‘II’’ side for high

speed or ‘‘I’’ side for low speed. Be sure that the

speed change lever is set to the correct position

before operation. Use the right speed for your job.

CAUTION:

•

Always set the speed change lever fully to the

correct position. If you operate the tool with the

speed change lever positioned half-way between

the ‘‘I’’ side and ‘‘II’’ side, the tool may be damaged.

•

Do not use the speed change lever while the tool is

running. The tool may be damaged.

Adjusting the fastening torque (Fig. 10)

The fastening torque can be adjusted in 17 steps by

turning the adjusting ring so that its graduations are

aligned with the pointer on the tool body. The fasten-

ing torque is minimum when the number 1 is aligned

with the pointer, and maximum when the

marking is aligned with the pointer.

The clutch will slip at various torque levels when set at

the number 1 to 16. The clutch is designed not to slip

at the

marking.

Before actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular applica-

tion.

NOTE:

•

The adjusting ring does not lock when the pointer is

positioned only half-way between the graduations.

•

Do not operate the tool with the adjusting ring set

between the number 16 and the

marking. The tool

may be damaged.

Screwdriving operation (Fig. 11)

Place the point of the driver bit in the screw head and

apply pressure to the tool. Start the tool slowly and

then increase the speed gradually. Release the trig-

ger as soon as the clutch cuts in.

NOTE:

•

Make sure that the driver bit is inserted straight in

the screw head, or the screw and/or bit may be

damaged.

•

When driving wood screws, predrill pilot holes to

make driving easier and to prevent splitting of the

workpiece. See the chart below.

Nominal diameter of

wood screw (mm)

Recommended size of

pilot hole (mm)

3.1 2.0 – 2.2

3.5 2.2 – 2.5

3.8 2.5 – 2.8

4.5 2.9 – 3.2

4.8 3.1 – 3.4

5.1 3.3 – 3.6

5.5 3.6 – 3.9

5.8 4.0 – 4.2

6.1 4.2 – 4.4

•

If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

Drilling operation

First, turn the adjusting ring so that the pointer on the

tool body points to the

marking. Then proceed as

follows.

•

Drilling in wood

When drilling in wood, best results are obtained with

wood drills equipped with a guide screw. The guide

screw makes drilling easier by pulling the bit into the

workpiece.

•

Drilling in metal

To prevent the bit from slipping when starting a hole,

make an indentation with a centerpunch and ham-

mer at the point to be drilled. Place the point of the

bit in the indentation and start drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be

drilled dry.

BDF460 (E) (’100. 4. 19)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita bdf 460 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita bdf 460

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info