Bedienungsanleitung Makita BFL121F (Seite 9 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

601006

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

OPERATION

Hold the tool firmly and place the socket over the bolt or

nut. Then switch the tool on. When the clutch cuts in, the

motor will stop automatically. Then release the switch

trigger.

NOTE:

• Hold the tool with its square drive pointed straight at the

bolt or nut, or the bolt or nut will be damaged.

Limits of fastening capacity (Fig. 11, 12, 13, 14,

15, 16)

Use the tool within the limits of fastening capacity. If you

use the tool beyond the limits, the clutch does not work.

And the tool cannot deliver enough fastening torque.

NOTE:

• The revolution angle means the angle which a screw/

bolt revolves when the tool attains to 100% from 50% of

desired torque.

• Use of a low temperature conditioned battery cartridge

may sometimes give warning for battery cartridge

capacity by warning lamp and beeper which makes the

tool stop immediately. In this case, the range of fasten-

ing capacity may be inferior to those shown in the

above even if a charged battery cartridge is used.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before attempting to perform

inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes. (Fig. 17)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps. (Fig. 18)

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

•Protector

• Various type of Makita genuine batteries and chargers

• Automatic refreshing adapter

• Angle head set

• Adjusting grip

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 70 dB (A) or less

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: screwdriving without impact

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been mea-

sured in accordance with the standard test method and

may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the oper-

ator that are based on an estimation of exposure in the

actual conditions of use (taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to

the trigger time).

ENH101-15

For European countries only

EC Declaration of Conformity

We Makita Corporation as the responsible manufac-

turer declare that the following Makita machine(s):

Designation of Machine: Cordless Angle Screwdriver

Model No./ Type: BFL060F, BFL080F, BFL081F,

BFL120F, BFL121F, BFL200F

are of series production and

Conforms to the following European Directives:

2006/42/EC

And are manufactured in accordance with the following

standards or standardised documents:

EN60745

The technical documentation is kept by our authorized

representative in Europe who is:

Makita International Europe Ltd.

Michigan Drive, Tongwell,

Milton Keynes, Bucks MK15 8JD, England

30. 1. 2009

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, 446-8502, JAPAN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BFL121F Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info